← IB Physics · HL · IB Physics revision
⭐ 0
IB Diploma Physics HL · B.5 Current and circuits (part 2)
Mini-Lesson

Current and circuits (part 2)

4 missions. Guess, learn, then check. Your place is saved.

  1. Mission 1A kettle's element gets very hot, yet the cable carrying the same current stays cool. Why?
  2. Mission 2One dead bulb can put out a whole string of lights, yet home lamps work on their own. Why?
  3. Mission 3Why do a car's headlights dim while its starter motor is turning?
  4. Mission 4A street lamp switches itself on at dusk. How does its circuit sense that it is getting dark?
Mission 1

Mission 1: A kettle's element gets very hot, yet the cable carrying the same current stays cool. Why?

Make a guess: A kettle's element gets very hot, yet the cable carrying the same current stays cool. Why?

Mission 1

Power: energy per second

Power: joules per second+−1 C1 C1 C1 C1 C1 C12 J per coulombtransferred here12 Vconventionalcurrentorange: carries energy · white: energygiven upV = 12 V: 12 J per coulombI = 3.0 A: 3.0 coulombs per second12 J C⁻¹ × 3.0 C s⁻¹ = 36 J s⁻¹P = IV = 36 W
  • Power = rate of energy transfer. 1 W = 1 J s⁻¹.
  • pd = joules per coulomb. Current = coulombs per second.
  • Multiply: joules per second.
  • P = IV.
Mission 1

Three forms of one law

  • Use V = IR: P = IV = I²R = V²/R.
  • Same current (in series): use I²R. Larger R → more power.
  • Same pd (in parallel): use V²/R. Smaller R → more power.
Quick check
?The potential difference across an ohmic resistor is increased so that the current in the resistor becomes three times as large. What is the ratio of the new power dissipated in the resistor, P2, to the original power, P1?
Mission 1

Energy transferred

  • Energy = power × time = IVt.
  • A heater on 12 V takes 3.0 A for 5.0 minutes.
  • P = 12 × 3.0 = 36 W. t = 5.0 × 60 = 300 s.
  • Energy = 36 × 300 = 1.1 × 10⁴ J.
  • Check: R = 12 ÷ 3.0 = 4.0 Ω; I²R = 3.0² × 4.0 = 36 W.
Quick check
?A steady current of 0.25 A flows in a 24 Ω resistor for 2.0 minutes. How much energy is dissipated in the resistor?
Mission 1

The heating effect

Kettle element and cablesupplyelement (large R)cable (tiny R)same IeverywherePower dissipated, P = I²R (same I)elementcabletinyBar lengths are qualitative.
  • Electrons collide with the lattice ions and pass on energy. The ions vibrate more: the resistor heats up.
  • Kettle element and its cable are in series: the same current.
  • P = I²R: the element's resistance is far larger, so nearly all the power is dissipated there.
  • The cable's resistance is tiny: very little heating.
  • Wanted heating: kettles, heaters. Unwanted: cables, chargers.
Quick check
?A 60 W lamp and a 100 W lamp are both designed to work on the same 230 V supply. Which lamp has the larger resistance when working normally, and why?
Mission check

?A 60 W lamp and a 100 W lamp are both rated for a 230 V supply. They are connected in series across a 230 V supply. Assume each keeps its normal working resistance. Which lamp is brighter?
Mission 2

Mission 2: One dead bulb can put out a whole string of lights, yet home lamps work on their own. Why?

Make a guess: One dead bulb can put out a whole string of lights, yet home lamps work on their own. Why?

Mission 2

Closed, open, short

Closed, open and short circuits(a) closed+lamp lit(b) open+no current(c) short circuit+lamp: no currentArrows: conventional current, + to −.Symbol keycellbatteryresistorswitch (open)variable resistorAammeterlampVvoltmeter
  • Charge flows only round a closed loop.
  • A gap anywhere in a loop (open circuit): no current in that loop.
  • Short circuit: a wire straight across a component. No potential difference across it, so no current through it.
Mission 2

Circuit diagrams

  • A circuit diagram shows what connects to what, not where things sit.
  • Conventional current flows from + to − round the external circuit.
  • A diagonal arrow through a symbol = variable component.
  • Ideal wires have no resistance. An ideal cell has no internal resistance.
Quick check
?Three circuits are each made from an identical cell of negligible internal resistance, a resistor and a lamp. In circuit 1 the three form a single closed loop. Circuit 2 is the same loop with an open switch added. Circuit 3 is the same loop as circuit 1 with a wire of negligible resistance connected directly across the lamp's terminals. Which ranks the currents I1, I2 and I3 in the lamps of circuits 1, 2 and 3?
Mission 2

Two conservation laws

Junction and loop3 A in2 A out1 A outin = out: 3 = 2 + 16 V2 V4 V+loop: 6 = 2 + 4
  • Junction: total current in = total current out. Charge is conserved: none piles up.
  • Closed loop: sum of emfs = sum of potential differences. Energy is conserved: each coulomb gains in the cell what it loses in the components.
  • Current is not used up. Energy is transferred.
Quick check
?A 9.0 V supply of negligible internal resistance is connected to three resistors in series. The potential differences across two of them are 2.0 V and 4.5 V. What is the potential difference across the third resistor?
Mission 2

Series and parallel

Series and parallelSeriesIIIIV₁V₂VSame current I everywhere. V = V₁ + V₂ParallelII₁I₂VVVSame V across each branch. I = I₁ + I₂string of lights: serieshouse lamps: parallelone pathfull supply pd each
  • Series: one path. Same current everywhere. pds add: V = V1 + V2.
  • Parallel: separate branches. Same pd across each. Currents add: I = I1 + I2.
  • Series: R = R1 + R2 + … Parallel: 1/R = 1/R1 + 1/R2 + …
  • Parallel: more paths, so the total is less than the smallest branch resistance.
  • Home lamps are in parallel: each has the full supply potential difference, whatever the others do.
Quick check
?Resistors of 3.0 Ω, 6.0 Ω and 8.0 Ω are connected in parallel. What is the equivalent resistance of the combination?
Mission 2

Worked example

Worked example circuit6.0 V1.0 Ω2.0 V3.0 Ω4.0 V6.0 Ω4.0 V2.0 A1.3 A0.67 A2.0 V + 4.0 V = 6.0 V1.3 A + 0.67 A = 2.0 A
  • 6.0 V supply, negligible internal resistance. A 1.0 Ω resistor in series with 3.0 Ω and 6.0 Ω in parallel.
  • Parallel pair: 1/R = 1/3.0 + 1/6.0 → 2.0 Ω.
  • Total: 1.0 + 2.0 = 3.0 Ω. Supply current: 6.0 ÷ 3.0 = 2.0 A.
  • Potential difference across the pair: 2.0 × 2.0 = 4.0 V. Across the 1.0 Ω: 2.0 V. Sum: 6.0 V.
  • Branch currents: 4.0 ÷ 3.0 = 1.3 A; 4.0 ÷ 6.0 = 0.67 A. Sum: 2.0 A.
Mission 2

Meters

Connecting metersAVammeter: in serieslampvoltmeter: across the lampIdeal ammeter: zero resistance.Ideal voltmeter: infinite resistance.
  • Ammeter: in series. Ideal: zero resistance, so it does not change the current.
  • Voltmeter: in parallel, across the component. Ideal: infinite resistance, so it draws no current.
  • Treat meters as ideal unless told otherwise.
  • Real meters change the circuit a little: a real ammeter adds resistance; a real voltmeter draws some current.
  • A real meter of known resistance: treat it as one more resistor in the circuit.
Quick check
?A student wants to measure the current in a lamp and the pd across it, but connects the meters the wrong way round. The circuit is: a cell, a voltmeter and the lamp connected in series in a single loop, with an ammeter connected in parallel with the lamp. Both meters are ideal. What does the student observe?
Mission check

?Three identical lamps are connected to a supply of negligible internal resistance: lamp A is in series with lamps B and C, which are in parallel with each other. The filament of lamp C breaks. What happens to the brightness of lamps A and B? (Assume each lamp's resistance stays the same.)
Mission 3

Mission 3: Why do a car's headlights dim while its starter motor is turning?

Make a guess: Why do a car's headlights dim while its starter motor is turning?

Mission 3

emf and internal resistance

A real cellreal cell (dashed box)+−emf 1.5 Vr = 0.50 ΩR = 2.5 ΩI = 0.50 AVreads the terminal pd: 1.25 VEnergy per coulomb (J C⁻¹ = V)gained: emf 1.5terminal pd 1.25 (outside)lost volts Ir = 0.25 (inside r)
  • emf: energy transferred to each coulomb of charge by the source.
  • A real cell has internal resistance r. Model: an ideal cell in series with r.
  • With a current, some energy per coulomb is dissipated inside the cell. That pd is the lost volts, Ir.
  • Terminal pd = emf − lost volts.
Mission 3

Terminal potential difference

  • ε = I(R + r). Terminal pd: V = ε − Ir (= IR).
  • No current: terminal pd = emf.
Quick check
?A battery with an internal resistance of 0.50 Ω drives a current of 0.60 A through a lamp, and an ideal voltmeter across the battery's terminals reads 4.2 V. The lamp is then disconnected, so that only the voltmeter remains connected across the battery. What does the voltmeter now read?
Mission 3

Worked example

  • Cell: emf 1.5 V, internal resistance 0.50 Ω. External resistor: 2.5 Ω.
  • Current = emf ÷ total resistance = 1.5 ÷ (2.5 + 0.50) = 0.50 A.
  • Lost volts = Ir = 0.50 × 0.50 = 0.25 V.
  • Terminal pd = 1.5 − 0.25 = 1.25 V.
  • Check: IR = 0.50 × 2.5 = 1.25 V.
Quick check
?A battery of emf 9.0 V and internal resistance 0.50 Ω is connected to a 4.0 Ω resistor. What is the terminal potential difference of the battery?
Mission 3

Consequences

Starter motor and headlightsheadlightsMswitchstarter motorrcar batteryTerminal pdopenclosedlights dimSwitch closed: large motor current, morelost volts.Bar lengths are qualitative.
  • More current → more lost volts → lower terminal pd.
  • A starter motor draws a very large current. The battery's terminal pd drops, so the headlights dim.
  • Short circuit (R = 0): current = emf ÷ r. Small r → a very large current; the cell heats up.
Quick check
?Cells P and Q have the same emf. P has a smaller internal resistance than Q. Each cell is connected in turn to the same lamp. Which statement is correct?
Mission 3

Measuring emf and r

Measuring emf and r+−Aswitchvariable resistorVacross the cellV / VI / A0intercept = emfgradient = −rV = −rI + emfSketch, no data.
  • Cell, variable resistor and ammeter in series. Voltmeter across the cell's terminals.
  • Change the resistance: record terminal pd V and current I each time.
  • V = −rI + emf: plot V against I. Straight line.
  • y-intercept = emf. Gradient = −r.
  • Switch off between readings: a warm cell's r changes.
Quick check
Graph of terminal pd V / V on the vertical axis (ticks at 0.5, 1.0, 1.5) against current I / A on the horizontal axis (tI / AV / V0.51.01.52.02.50.51.01.5
?The graph shows how the terminal pd V of a cell varies with the current I that it delivers. What is the internal resistance of the cell?
Mission check

?A battery of internal resistance r is connected to an external resistor whose resistance equals r. The external resistor is then replaced by one of resistance 2r. How does the potential difference across the terminals of the battery change?
Mission 4

Mission 4: A street lamp switches itself on at dusk. How does its circuit sense that it is getting dark?

Make a guess: A street lamp switches itself on at dusk. How does its circuit sense that it is getting dark?

Mission 4

Sharing a pd

Potential divider+−VinR₁R₂IIV₁V₂Same current I in both. Bigger R, biggershare of Vin.
  • Two resistors in series across a supply Vin carry the same current.
  • So the pd splits in proportion to resistance. Bigger R, bigger share.
  • Use V = IR twice: I = Vin/(R1 + R2), then V2 = IR2.
Mission 4

Worked example

  • 12 V supply, negligible internal resistance. R1 = 2.2 kΩ, R2 = 3.3 kΩ. Find the pd across R2.
  • I = 12 ÷ 5500 = 2.18 × 10⁻³ A. V2 = 2.18 × 10⁻³ × 3300 = 7.2 V.
  • The pd across R1 is 12 − 7.2 = 4.8 V. Ratio 4.8 : 7.2 = 2.2 : 3.3.
Quick check
?An LDR and a 300 Ω resistor are in series across a 6.0 V supply of negligible internal resistance. In the room's light the LDR's resistance is 900 Ω. What does an ideal voltmeter across the 300 Ω resistor read?
Mission 4

Potentiometer

Potentiometer+−Vinuniform tracksliding contactABVreads the pd between A andthe sliderUniform track: pd from A ∝ distance from AVin0pdABdistance from A
  • A resistance track across the supply, with a sliding contact.
  • Output between one end and the slider: any pd from 0 to Vin.
  • Uniform track: pd ∝ length from that end.
Quick check
?A potentiometer has a uniform resistance track connected across a 9.0 V dc supply of negligible internal resistance. An ideal voltmeter is connected between one end of the track and the sliding contact, which is one third of the way along the track from that end. What does the voltmeter read?
Mission 4

Sensors in a divider

Thermistor and LDRNTC thermistorLDRresistancetemperaturefalls as it warmsresistancelight intensityfalls in brighterlightSketch graphs, no scale.
  • NTC thermistor: R falls as temperature rises.
  • LDR: R falls as light gets brighter.
  • Put one in a divider: when its R changes, its share of the pd changes.
  • A component's pd rises when its share of the total R rises.
Mission 4

Control circuits

Sensing circuits(a) Dusk lamp: Vout across the LDR+−VinvariableLDRVoutswitchingcircuitlampDarker → LDR's R up → Vout up → lamp on.(b) Heating: Vout across the thermistor+−VinvariablethermistorVoutswitchingcircuitheaterColder → thermistor's R up → Vout up →heater on.
  • Dusk lamp: Vout across the LDR. Darker → LDR's R up → Vout up → switches the lamp on.
  • Heating control: Vout across the thermistor. Colder → R up → Vout up → switches the heater on.
  • Make the fixed resistor variable to set the switching point.
  • Vout goes to a switching circuit, not straight to the lamp or heater.
Quick check
?An LDR and a 10 kΩ fixed resistor are in series across a 6.0 V supply of negligible internal resistance. An ideal voltmeter is connected across the fixed resistor. The LDR's resistance is 50 kΩ in the dark and 1.0 kΩ in bright light. What does the voltmeter read in each case?
Mission check

?An NTC thermistor and a fixed resistor are in series across a supply of constant pd. An ideal voltmeter is connected across the thermistor. The thermistor is warmed. What happens to the voltmeter reading?
Recap

The big ideas

Mission 1

  • P = IV = I²R = V²/R; energy = IVt. Same current: larger R, more power. Same pd: smaller R, more power.

Mission 2

  • Junction: current in = current out (charge). Loop: emfs = sum of potential differences (energy).
  • Series: same I, pds add, R = R1 + R2. Parallel: same V, currents add, 1/R = 1/R1 + 1/R2.
  • Ideal ammeter: zero resistance, in series. Ideal voltmeter: infinite resistance, in parallel.

Mission 3

  • ε = I(R + r); terminal pd V = ε − Ir.
  • Graph of V against I: intercept = emf, gradient = −r.

Mission 4

  • Series resistors share the pd in proportion to resistance: same current, V = IR.
  • Thermistor or LDR in a divider: its share of the pd changes with temperature or light.
🏆

Mini-lesson complete!

⭐⭐⭐

You've worked through Current and circuits (part 2) for IB Physics HL. 🎉

  1. Mission 1A kettle's element gets very hot, yet the cable carrying the same current stays cool. Why?
  2. Mission 2One dead bulb can put out a whole string of lights, yet home lamps work on their own. Why?
  3. Mission 3Why do a car's headlights dim while its starter motor is turning?
  4. Mission 4A street lamp switches itself on at dusk. How does its circuit sense that it is getting dark?

Your stars: 0 / 0

📣 Smashed it? Share your score

Challenge a friend to beat your stars, or show a parent how you got on.

→ Back to IB Physics · HL