← AP Physics C: E&M
⭐ 0
AP Physics C: E&M · Unit 13: Electromagnetic Induction (part 2)
Mini-Lesson

AP® Physics C: E&M Unit 13: Electromagnetic Induction (Part 2)

3 missions. Guess, learn, then check. Your place is saved.

Covers College Board topics 13.2, 13.4–13.6

Short, curiosity-driven missions (about 20 minutes each) that teachers can assign. Use them alongside AP Classroom practice.

  1. Mission 1Close a switch in a circuit with a large coil. Why does the current take time to reach its full value?
  2. Mission 2Connect a charged capacitor to a coil, with no battery. Why does the charge swing back and forth?
  3. Mission 3Light crosses empty space with nothing to carry it. What keeps the wave going?

AP® is a trademark registered by the College Board, which is not affiliated with, and does not endorse, this website.

Mission 1Topics 13.4, 13.5

Mission 1: Close a switch in a circuit with a large coil. Why does the current take time to reach its full value?

Make a guess: Close a switch in a circuit with a large coil. Why does the current take time to reach its full value?

Mission 1

Switching on an LR circuit

An LR circuit being switched on+−εswitchRLIloop+−inductor emfopposes the batteryJust after closing: I = 0, inductor emf = εε − IR − L dI/dt = 0
  • Battery ε, resistor R, ideal inductor L, in series. Switch closed at t = 0.
  • Loop rule: ε − IR − L dI/dt = 0, so ε = IR + L dI/dt.
  • Just after closing: I = 0, so the inductor's emf is ε, opposing the battery. dI/dt = ε/L.
  • Long after: I steady, dI/dt = 0. The inductor acts as a plain wire. I = ε/R.
Quick check
?A series circuit contains an ideal 9.0 V battery, a 25 Ω resistor, an ideal inductor and a switch. The switch is closed at t = 0. At a later instant, the current in the circuit is 0.24 A. What is the magnitude of the potential difference across the inductor at that instant?
Mission 1

Solving the loop equation

Current growth in an LR circuitI (A)t (ms)00.600.3863 % at τε/Rtangent255075τε = 12 V, R = 20 Ω, L = 0.50 H|ΔVL| (V)t (ms)01237 % at τstarts at ε255075
  • Solution with I(0) = 0: I = (ε/R)(1 − e−t/τ), with τ = L/R.
  • Check: dI/dt = (ε/L)e−t/τ. Then IR + L dI/dt = ε(1 − e−t/τ) + εe−t/τ = ε. ✓
  • Potential difference across the inductor: |ΔVL| = εe−t/τ: starts at ε, decays to zero.
  • Energy stored ½LI² also rises to a steady value, ½L(ε/R)².
Mission 1

What τ means

Current growth in an LR circuitI (A)t (ms)00.600.3863 % at τε/Rtangent255075τε = 12 V, R = 20 Ω, L = 0.50 H|ΔVL| (V)t (ms)01237 % at τstarts at ε255075
  • At t = τ, I = (1 − e⁻¹) × final ≈ 63 % of the final current.
  • Rising at its initial rate ε/L, the current would reach ε/R in exactly τ.
  • Bigger L: slower. Bigger R: faster (τ = L/R), and a smaller final current.
  • Use Req: the resistance the inductor's current actually passes through.
Mission 1

Worked example

  • ε = 12 V, R = 20 Ω, L = 0.50 H.
  • τ = 0.50/20 = 25 ms. Final current 12/20 = 0.60 A.
  • At t = 25 ms: I = 0.60(1 − e⁻¹) = 0.38 A.
  • Initial rate: ε/L = 24 A/s. 24 A/s × 0.025 s = 0.60 A: the tangent reaches the final value at τ.
Quick check
?A series circuit contains an ideal battery of emf ε, a resistor of resistance R, an ideal inductor of inductance L and a switch. The switch is closed at t = 0. At what time t is the energy stored in the inductor one-quarter of its final value?
Mission 1

Switching off: decay

Current decay through a resistorrεopenedat t = 0LRI₀, samedirectionSwitch opened: L keeps I₀ flowing, through RIt0I₀0.37I₀τI = I₀e−t/ττ = L/Req of the loop it decays throughSketch graph.
  • Inductor carrying I0 is connected across a resistor, with no battery.
  • I = I0e−t/τ, τ = L/Req of the loop it decays through.
  • At t = τ: 37 % of I0 remains.
  • Just after switching, the inductor keeps the current I0 flowing: its emf is I0Req, which can be larger than the battery's emf.
  • Example: 0.60 A in 0.50 H, diverted through 100 Ω. τ = 5.0 ms; emf just after = 0.60 × 100 = 60 V.
Mission 1

Where the energy goes

  • The stored energy ½LI0² is dissipated in the resistors as the current decays.
  • Decay example above: ½ × 0.50 × 0.60² = 0.090 J, all to the 100 Ω resistor.
  • The inductor does not dissipate energy: an ideal inductor has no resistance.
  • No path for the current (switch simply opened): dI/dt is enormous, and the emf can spark across the switch.
Quick check
?An ideal inductor of inductance 0.40 H carries a steady current of 4.0 A. At t = 0 a switch disconnects the battery and, at the same instant, connects the inductor across a 12 Ω resistor, so the current decays in the loop formed by the inductor and the resistor. How much energy is dissipated in the resistor between t = 0 and t = τ, where τ is the time constant of that loop?
Quick check
Circuit diagram. A battery, labeled ε, is on the left side with its positive terminal (+) at the top. The top wire runs +εSR₁LR₂
?In the circuit shown, the battery and the inductor are ideal, and switch S is initially open. S is closed at t = 0. I0 is the current in resistor R2 just after S is closed, and If is the current in R2 a long time after S is closed. Which statement is correct?
Mission check

Three circuit diagrams side by side, labeled Circuit 1, Circuit 2 and Circuit 3. In each, a battery is on the left side,Circuit 1LRCircuit 2LRRCircuit 3LRR
?The diagram shows three circuits, each with an identical ideal battery. Every resistor has resistance R, and the ideal inductor in each circuit has inductance L. τ1, τ2 and τ3 are the time constants of Circuits 1, 2 and 3. Which ranking of the time constants is correct?
Mission 2Topics 13.4, 13.6

Mission 2: Connect a charged capacitor to a coil, with no battery. Why does the charge swing back and forth?

Make a guess: Connect a charged capacitor to a coil, with no battery. Why does the charge swing back and forth?

Quick check
?Predict first. A charged capacitor is connected across an ideal inductor at t = 0, with no resistance in the circuit. Which describes the charge on the capacitor after t = 0?
Mission 2

One cycle, step by step

One cycle of an LC circuitt = 0+−I = 0UCULt = T/4I maxC emptyUCULt = T/2−+I = 0UCULt = 3T/4I maxC emptyUCUL
  • Start: capacitor charged to Q0, current zero. All energy in the capacitor.
  • It discharges through L. The inductor makes the current grow gradually.
  • Capacitor empty: current maximum. All energy in the inductor's field.
  • The inductor keeps the current going, charging the capacitor the opposite way.
  • Then the current reverses, and the cycle repeats. No resistance: it goes on forever with constant amplitude.
Mission 2

Energy is conserved

Energy shared between C and Lq = Q₀UCq = Q₀/2¼¾q = 0ULtotal Q₀²/(2C)Total energy is the same at every instantUC = q²/(2C)UL = ½LI²Half the charge: a quarter of the energy in C.
  • At every instant: q²/(2C) + ½LI² = Q0²/(2C).
  • Maximum current when q = 0: ½LImax² = Q0²/(2C).
  • Imax = Q0/√(LC). Starting from potential difference ΔV0: Imax = ΔV0√(C/L).
  • Larger L: smaller Imax, since Imax ∝ 1/√L.
Mission 2

Worked example

  • C = 10 μF charged to 20 V, then connected across L = 25 mH.
  • Q0 = CΔV0 = 2.0 × 10⁻⁴ C. Energy ½CΔV0² = 2.0 × 10⁻³ J.
  • Imax = Q0/√(LC) = 2.0 × 10⁻⁴/√(2.5 × 10⁻⁷) = 0.40 A.
  • Check: ½LImax² = ½ × 0.025 × 0.40² = 2.0 × 10⁻³ J. ✓
Quick check
?A 20 μF capacitor is charged to a potential difference of 12 V and then connected across an ideal 50 mH inductor, with no other elements in the circuit. What is the maximum current in the inductor?
Mission 2

The SHM equation

Charge, current and energy in an LC circuittQ₀−Q₀q = Q₀cos ωtI = −ωQ₀sin ωtT/4T/23T/4TI peaks when q = 0; I = 0 at the q extremesenergyttotal0T/2TUC ∝ cos²ωtUL ∝ sin²ωtEach repeats every T/2; they add to the total.
  • SHM: any quantity obeying d²x/dt² = −ω²x oscillates as x = A cos ωt, with ω set by the system.
  • Loop rule: q/C + L dI/dt = 0, with I = dq/dt.
  • So d²q/dt² = −q/(LC): the same form as a = −ω²x.
  • ω = 1/√(LC); period T = 2π√(LC).
  • q = Q0 cos ωt; I = dq/dt = −ωQ0 sin ωt. Current peaks when q = 0.
  • Analogy: q ↔ x, I ↔ v, L ↔ m, 1/C ↔ k.
  • Worked example above: ω = 1/√(2.5 × 10⁻⁷) = 2.0 × 10³ rad/s.
Quick check
?An ideal LC circuit has an inductance of 80 mH and a capacitance of 5.0 μF. What is the angular frequency of its oscillations?
Quick check
Circuit diagram of a single loop containing an open switch S on the top wire, an inductor L on the left side, a capacitoSLC2C
?Capacitor C in the circuit shown is initially charged, capacitor 2C is initially uncharged, and the inductor is ideal. Switch S is then closed. What is the angular frequency of the resulting oscillations of charge?
Mission 2

Energy sloshing in time

Charge, current and energy in an LC circuittQ₀−Q₀q = Q₀cos ωtI = −ωQ₀sin ωtT/4T/23T/4TI peaks when q = 0; I = 0 at the q extremesenergyttotal0T/2TUC ∝ cos²ωtUL ∝ sin²ωtEach repeats every T/2; they add to the total.
  • UC = (Q0²/2C) cos²ωt; UL = (Q0²/2C) sin²ωt. They always add to Q0²/(2C).
  • Each energy swings between zero and the total twice per cycle of q.
Quick check
?In an ideal LC circuit, at t = 0 the capacitor (capacitance C) has charge Q0 and the current is zero; the inductor has inductance L. At what time t does the energy stored in the inductor first equal the energy stored in the capacitor?
Mission check

Graph of q against t. The vertical axis is marked Q₀, 0 and −Q₀, with dashed lines at Q₀ and −Q₀. The curve is a cosine:PQRQ₀−Q₀0qt
?The graph shows the charge q on the capacitor of an ideal LC circuit as a function of time t. Which ranks the magnitudes of the current in the circuit at the instants P, Q and R?
Mission 3Topic 13.2

Mission 3: Light crosses empty space with nothing to carry it. What keeps the wave going?

Make a guess: Light crosses empty space with nothing to carry it. What keeps the wave going?

Mission 3

Four equations, all of electromagnetism

Maxwell's four equations1. Gauss (E)∮E·dA = qenc/ε₀Charges are sources of E.2. Gauss (B)∮B·dA = 03. Faraday∮E·dℓ = −dΦB/dtChanging B flux: circulating E.4. Ampère–Maxwell∮B·dℓ = μ₀I + μ₀ε₀ dΦE/dtCurrent or changing E flux: circulating B.
  • 1. Gauss (E): ∮E·dA = qenc/ε0. Charges are sources of electric field.
  • 2. Gauss (B): ∮B·dA = 0. No magnetic charges.
  • 3. Faraday: ∮E·dℓ⃗ = −dΦB/dt. A changing magnetic flux makes a circulating electric field.
  • 4. Ampère–Maxwell: ∮B·dℓ⃗ = μ0I + μ0ε0 dΦE/dt. Currents and changing electric flux make a circulating magnetic field.
  • With the force on a charge, these fully describe electromagnetism.
Quick check
?Gauss's law is the first of Maxwell's equations, the set of equations that together fully describe electromagnetism. Which statement about Gauss's law is correct?
Mission 3

Equation 1: Gauss's law

  • Holds for every closed surface, any shape, any charges inside or outside.
  • Net flux out depends only on the enclosed charge.
  • Symmetry (sphere, cylinder, plane) only makes it easy to use for finding E.
  • Field lines that start or end do so on charges. (Induced E fields, equation 3, form closed loops instead.)
Mission 3

Equation 2: no magnetic charges

Magnetic field lines form closed loopsSNclosed surface:6 in, 6 outInside the magnet the lines run S → N.∮B·dA = 0
  • ∮B·dA = 0 for every closed surface.
  • Magnetic field lines form closed loops: out of N, around, into S, back through the magnet.
  • Every line that leaves a closed surface comes back in. Net flux: zero.
  • So there are no monopoles: no point where field lines simply begin.
Quick check
Side view of a horizontal bar magnet, S on the left and N on the right, with field lines: outside the magnet they leave SNregion 1region 2region 2
?The figure shows a bar magnet and some of its field lines. The dashed line is the edge view of a flat plane that cuts through the middle of the magnet, perpendicular to it, and extends indefinitely. Region 1 is the part of the plane inside the magnet; region 2 is all the rest of the plane. How do the magnitudes of the magnetic flux through region 1 and through region 2 compare?
Mission 3

Equation 3: induced electric field

Induced electric field of a solenoidREB out of the page,increasingE loops:clockwiseE (10⁻³ V/m)r (m)0.040.080.125105.04.0peak at r = RRate of change of B = 0.50 T/s. Cross-sectionto scale.
  • ∮E·dℓ⃗ = −dΦB/dt. The emf around a loop is the circulation of an induced E field.
  • The field exists with or without a wire. A wire just lets charges respond.
  • Its lines are closed loops: not conservative, so no potential can describe it.
  • Long solenoid, radius R, B = βt inside. Circle of radius r about the axis:
  • Inside (r < R): E(2πr) = πr²β → E = rβ/2.
  • Outside (r > R): E(2πr) = πR²β → E = R²β/(2r). Nonzero, though B ≈ 0 there.
  • R = 0.040 m, β = 0.50 T/s: at r = 0.020 m, E = 5.0 × 10⁻³ V/m; at r = 0.10 m, E = 4.0 × 10⁻³ V/m.
Quick check
?An electron is held at rest at a point outside a long solenoid, where the solenoid's magnetic field is negligible. The current in the solenoid begins to increase, and the electron is released. Which describes the force on the electron just after it is released?
Quick check
?A parallel-plate capacitor is being charged, with a steady current in the wires connected to its plates. Which statement about the region between the plates is correct?
Mission 3

Equation 4: a changing E field makes B

Magnetic field of a charging capacitorIIE increasingBBBSame sense around the wire and around the gap.
  • Ampère: a current makes a circulating B field.
  • Maxwell's addition: a changing electric field also makes one, just as a changing B field makes E.
  • Charging capacitor: no charge crosses the gap, yet the growing E field between the plates is circled by a B field.
  • You will not need to calculate with the changing-E term. Know that it exists and what it does.
Mission 3

Light

Electromagnetic waveEBvelocity cE ⟂ B ⟂ velocity · E and B in phaseA snapshot at one instant.
  • Equations 3 and 4 together: a changing B makes E, a changing E makes B.
  • In empty space, with no charges or currents, the two can sustain each other and travel: an electromagnetic wave.
  • Maxwell's equations give its speed in free space: c = 1/√(ε0μ0).
  • 1/√(4π × 10⁻⁷ × 8.85 × 10⁻¹²) = 3.00 × 10⁸ m/s: the measured speed of light.
  • Same speed for every frequency. No medium needed. Derivation: not required.
Quick check
?Suppose the permittivity of free space were four times its actual value, with the permeability unchanged. What speed would Maxwell's equations then predict for electromagnetic waves in a vacuum?
Mission check

?A region of empty space contains no charges and no currents. At one instant, the electric field throughout the region points in the +x direction and its magnitude is increasing steadily. Which statement follows from Maxwell's equations?
Recap

The big ideas

Mission 1

  • ε = IR + L dI/dt. Growth I = (ε/R)(1 − e−t/τ); decay I = I0e−t/τ; τ = L/Req.
  • Just after switching, an inductor's current is unchanged; a long time later it is a plain wire. Stored energy ends up dissipated in the resistors.

Mission 2

  • LC circuit: q²/(2C) + ½LI² = constant; Imax = Q0/√(LC).
  • d²q/dt² = −q/(LC): SHM with ω = 1/√(LC).

Mission 3

  • Maxwell's four equations: Gauss (E), Gauss (B) = 0, Faraday (changing B → circulating E), Ampère–Maxwell (current or changing E → circulating B).
  • Together they predict EM waves in free space at c = 1/√(ε0μ0) = 3.00 × 10⁸ m/s.
🏆

Mini-lesson complete!

⭐⭐⭐

You've worked through Electromagnetic Induction (part 2) for AP Physics C: E&M. 🎉

  1. Mission 1Close a switch in a circuit with a large coil. Why does the current take time to reach its full value?
  2. Mission 2Connect a charged capacitor to a coil, with no battery. Why does the charge swing back and forth?
  3. Mission 3Light crosses empty space with nothing to carry it. What keeps the wave going?

Your stars: 0 / 0

📣 Smashed it? Share your score

Challenge a friend to beat your stars, or show a parent how you got on.

→ Back to AP Physics C: E&M