← AP Physics 2
⭐ 0
AP Physics 2 · Unit 12: Magnetism and Electromagnetism
Mini-Lesson

AP® Physics 2 Unit 12: Magnetism and Electromagnetism

7 missions. Guess, learn, then check. Your place is saved.

Covers College Board topics 12.1–12.4

Short, curiosity-driven missions (about 20 minutes each) that teachers can assign. Use them alongside AP Classroom practice.

  1. Mission 1Switch on a current in a wire just above a compass. Which way does the needle turn, and why?
  2. Mission 2A magnet grabs an iron nail but ignores a copper pipe. What is different inside the iron?
  3. Mission 3A wire carrying a current lies between the poles of a magnet. Which way is it pushed?
  4. Mission 4A magnetic field can steer a beam of charged particles. Can it also make them go faster?
  5. Mission 5Two parallel wires carry currents in the same direction. Do they attract or repel, and why?
  6. Mission 6Drop a strong magnet down a copper pipe and it falls in slow motion. Why?
  7. Mission 7Move a metal rod or spin a coil near a magnet, and a voltage appears. What decides how big it is?

AP® is a trademark registered by the College Board, which is not affiliated with, and does not endorse, this website.

Mission 1Topics 12.1, 12.3

Mission 1: Switch on a current in a wire just above a compass. Which way does the needle turn, and why?

Make a guess: Switch on a current in a wire just above a compass. Which way does the needle turn, and why?

Mission 1

Where magnetic fields come from

Sources of magnetic fieldsNSPermanent magnet:makes a fieldICurrent (movingcharges): makes a fieldNS+at restCharge at rest:no magnetic force
  • A magnetic field is produced by moving charges (an electric current) and by permanent magnets.
  • It exerts forces on moving charges, currents and magnetic materials (iron, steel).
  • A charge at rest feels no magnetic force.
Mission 1

Field lines

Bar magnet field linesNSOutside: N to SInside: S to N(dashed)compass:red end = N
  • Direction of a field line: the way the north end of a compass needle points.
  • Closer lines = stronger field. Lines never cross.
  • Field lines are closed loops: outside a magnet they run N → S; inside, S → N.
  • Bar magnet: lines leave the N pole, curve around, enter the S pole, and continue back through the magnet.
Quick check
?Point C is at the center of a bar magnet, inside it. Point D is just outside the magnet, beside its center. How does the magnitude of the magnetic field at C compare with that at D?
Mission 1

Field of a long straight wire

Field of a straight wireICurrent up the wireRight-hand rule:thumb = currentfingers = field⊙ current out of page⊗ current into pageEnd-on viewsGaps grow with distance: the field weakens.
  • Field lines are concentric circles centered on the wire, in planes at right angles to it.
  • Right-hand rule: thumb along the current; curled fingers give the field direction.
  • Lines spread out with distance: the field gets weaker away from the wire.
  • End-on views: ⊙ current out of the page → field counterclockwise; ⊗ into the page → clockwise.
Quick check
?A long, straight, vertical wire carries a steady current upward. Point P is 5.0 cm due east of the wire, level with it. What is the direction of the magnetic field of the wire at P?
Mission 1

Flat coil and solenoid

Flat coil and solenoidFlat coil (cross-section)current outcurrent inField along the axis through the middle.Solenoid (cross-section)NSTop row: current out. Bottom row: in.Right hand: fingers round the turns withthe current, thumb along the field inside.Solenoid: outside loops drawn closer than toscale.
  • Flat coil: the circles around each part of the wire combine. At the center the field is along the axis.
  • Solenoid (long coil): inside, straight, parallel, evenly spaced lines (uniform field). Outside, the pattern of a bar magnet.
  • Direction: curl the fingers of your right hand the way the current flows around the turns; the thumb points along the field inside, toward the coil's N end.
Quick check
?You look at the left end of a long solenoid. Seen from there, the current in its turns flows clockwise. Which end of the solenoid is its north end?
Mission 1

Compasses and Earth

Earth as a dipolegeographic North Polemagnetic south poleField lines enter Earth in the northernhemisphere.Tilt of the magnetic axis about 10°; it variesover time. Not to scale.
  • A compass needle is a small dipole. It turns to align with the net field where it is.
  • Earth's field ≈ a dipole. Near the geographic North Pole is a magnetic south pole, so compass N ends point north.
Quick check
Diagram: a circle labeled Earth, with a dashed vertical line through its center from Geographic north (top) to GeographiGeographic northGeographic southEarthP
?The diagram shows the shape of Earth's magnetic field lines, without arrows, in a plane through Earth's geographic poles. A compass needle mounted so that it can turn in this vertical plane is placed at point P, on Earth's surface. In which direction does the north end of the needle point?
Mission check

?A flat horizontal circular coil carries a steady current that flows clockwise when viewed from above. What is the direction of the magnetic field at the center of the coil?
Mission 2Topic 12.1

Mission 2: A magnet grabs an iron nail but ignores a copper pipe. What is different inside the iron?

Make a guess: A magnet grabs an iron nail but ignores a copper pipe. What is different inside the iron?

Mission 2

Magnetism comes from moving charge

A current loop is a magnetic dipoleISNcurrent loopSNbar magnetIn an atom+−electron motioncurrent: opposite waya tiny current loopField lines computed for each source, in aplane through its axis.
  • A charge at rest makes no magnetic field.
  • A loop of current makes a field like a tiny bar magnet: a magnetic dipole.
  • In atoms, electrons move around nuclei and spin. Each atom can act as a tiny dipole.
  • A material is magnetized when many of these dipoles point the same way.
  • A dipole's field gets weaker with distance.
  • Every magnet is a dipole. No isolated north or south pole has ever been found.
Quick check
?Which of the following produces a magnetic field? Ignore Earth's field and Earth's motion.
Quick check
?An iron nail does not attract a steel paper clip. After the nail has been stroked several times in one direction with one pole of a strong magnet, it does attract the paper clip. Which explanation of these observations is correct?
Mission 2

Domains

Magnetic domainsNo fieldrandom:fields cancelIn a fieldaligneddomains growField removedmany stayalignedexternal fieldBreak a magnet: each piece has N and SNSNSNSSchematic, not to scale. Arrows: the directionof the aligned atomic dipoles in each domain.
  • In iron, atomic dipoles line up with their neighbors in small regions: domains.
  • Unmagnetized iron: domains point in random directions. Their fields cancel.
  • In an external field, domains along the field grow and others turn. The iron becomes a magnet: induced magnetism.
  • The near end becomes the opposite pole, so iron is attracted to either pole.
  • Field removed: in some materials many domains stay aligned: a permanent magnet.
  • Break a magnet: each piece is a complete dipole with its own N and S.
Mission 2

Three kinds of material

Three kinds of magnetic materialNSironferromagneticstronglyattractedNSaluminumparamagneticweaklyattractedNSbismuthdiamagneticweakly repelledfieldNot to scale: deflections exaggerated. Bluearrows: atomic dipoles along (iron, aluminum)or opposite (bismuth) the field.
  • Ferromagnetic (iron, nickel, cobalt): dipoles align strongly with the field; can stay aligned. Strongly attracted; can become permanent magnets.
  • Paramagnetic (aluminum, titanium, magnesium): dipoles align weakly with the field; alignment is lost when the field goes. Weakly attracted.
  • Diamagnetic (every material; it dominates in copper, water, bismuth): a weak alignment opposite the field. Weakly repelled.
  • Iron is diamagnetic too, but its ferromagnetism swamps the effect.
Quick check
Four graphs, numbered 1 to 4, each of M (vertical axis, with zero in the middle) against time t (horizontal axis), with 1Mtt₁t₂2Mtt₁t₂3Mtt₁t₂4Mtt₁t₂
?An aluminum rod is placed in a strong external magnetic field at time t1, and the field is removed at time t2. In each graph shown, M is the net alignment of the rod's atomic dipoles along the direction of the external field (positive when along the field). Which graph best represents the aluminum rod?
Mission 2

Permeability

Magnetization against external fieldmagnetization Mexternal field Bext0ironflattensaluminumcopperSketch, no values. Aluminum and copper linesgreatly exaggerated.
  • Permeability μ: how strongly a material becomes magnetized in response to an external field.
  • Free space: the vacuum permeability μ0 = 4π × 10⁻⁷ T·m/A, a constant. It appears in B = μ0I/(2πr).
  • Matter's permeability differs from μ0, depending on its composition: dipoles that align along the field raise μ above μ0; a response opposite the field lowers it.
  • Iron: far greater than μ0 (hundreds to thousands of times).
  • μ of a material is not a constant. It changes with temperature, field strength, orientation and composition.
  • Example: in a strong field iron's domains are nearly all aligned, so extra field adds little magnetization. Its μ falls.
Quick check
Graph of M (arbitrary units), with axis marks 2, 4, 6, 8 and 10, against B ext (mT), with axis marks 0, 10, 20, 30 and 4M (arbitrary units)Bext(mT)010203040246810XYZ
?Three samples, X, Y and Z, of different materials are identical in size and shape. Each is placed in an external magnetic field Bext, and its magnetization M, the net alignment of its atomic dipoles, is measured. The graph shows the results. Which ranks the magnetic permeabilities of the three materials, from greatest to least?
Mission check

?Rods of nickel, aluminum and copper, identical in size and shape, are each placed in turn in a strong external magnetic field and then removed from it. Which of the rods can then be a permanent magnet?
Mission 3Topic 12.3

Mission 3: A wire carrying a current lies between the poles of a magnet. Which way is it pushed?

Make a guess: A wire carrying a current lies between the poles of a magnet. Which way is it pushed?

Mission 3

The motor effect

The motor effectCurrent across thefieldNSCurrent along thefieldNSFcurrent out of thepagecurrentF = 0
  • A current-carrying wire in a magnetic field feels a force.
  • The force is at right angles to both the current and the field.
  • No force when the current is parallel to the field.
  • Reverse the current or the field: the force reverses.
Mission 3

Which way?

Direction of the forceRight-hand rulefingers: B, into the pagethumb: I, up the pagepalm pushes: F, to the leftIF× : B into the page
  • Right-hand rule: fingers along B, thumb along I; the force comes out of your palm.
Quick check
?A straight wire in the plane of the page carries a current toward the right side of the page through a uniform magnetic field directed into the page. What is the direction of the magnetic force exerted on the wire?
Mission 3

How big?

Size of the force on a wireuniform field BIℓℓ = length inside the fieldθI sin θI cos θ: no forceθ = angle between the current and the field
  • FB = IℓB sin θ
  • θ = angle between the current and the field. Largest at 90°, zero at 0°.
  • The length is the length inside the field.
  • B is in tesla (T).
Mission 3

Worked example

  • A 4.0 cm length of wire carries 2.5 A at right angles to a 0.15 T field.
  • Force = 0.15 × 2.5 × 0.040 = 0.015 N.
  • Turn the wire to 30° to the field: F = 0.015 × sin 30° = 0.0075 N.
  • Backward: 0.012 N on a 5.0 cm wire carrying 3.0 A at right angles. B = force ÷ (current × length) = 0.012 ÷ (3.0 × 0.050) = 0.080 T.
Quick check
A shaded rectangular region of uniform magnetic field, with horizontal field lines pointing to the right, labeled B = 0.30°I = 4.0 AB = 0.60 TLength in field 0.25 m; total length 0.40 m
?The figure shows a straight wire carrying a current across a region of uniform magnetic field (shaded); the field is zero outside the region. What is the magnitude of the magnetic force exerted on the wire?
Mission check

?A long straight wire carries a current vertically upward. It is in a uniform horizontal magnetic field that points due north. In which direction is the magnetic force on the wire?
Mission 4Topic 12.2

Mission 4: A magnetic field can steer a beam of charged particles. Can it also make them go faster?

Make a guess: A magnetic field can steer a beam of charged particles. Can it also make them go faster?

Mission 4

Force on a moving charge

Force on a moving chargeB into the pagevF+Moving along the fieldB+vF = 0+at restF = 0
  • A current is moving charge, so a single moving charge in a field also feels a force.
  • F = qvB sin θ
  • θ = angle between v and B.
  • Zero force on a charge at rest, or moving along the field.
  • Example: an electron at 3.0 × 10⁶ m/s at right angles to a 0.20 T field: F = 1.60 × 10⁻¹⁹ × 3.0 × 10⁶ × 0.20 = 9.6 × 10⁻¹⁴ N.
  • Magnetic forces act between moving charges: a charge at rest neither feels one nor exerts one.
Mission 4

Which way?

Which way is the force?Right-hand rule (positive charge)thumb: vpalm pushes: Ffingers: B, into the pagevF+protonvF−electronnegative charge: force the other way
  • Right-hand rule for a positive charge: fingers along B, thumb along v, force out of the palm. Negative charge: force the other way.
  • The force is always ⟂ to the velocity, so it does no work: the speed and kinetic energy never change.
Quick check
?An electron moves toward the right side of the page through a uniform magnetic field directed out of the page. What is the direction of the magnetic force exerted on the electron at this instant?
Mission 4

Circular paths

Circular path in a magnetic fieldB out of the page+vF+vF+vFForce always at right angles to the velocity:speed constant.
  • Only the direction changes. Uniform field, v ⟂ B: a circle.
  • The magnetic force is the centripetal force: magnetic force = mv²/r.
  • r = mv/(Bq)
  • Faster or heavier → bigger circle. Stronger field or more charge → tighter circle.
  • Time for one orbit: T = 2πr/v = 2πm/(Bq).
Mission 4

Worked example

  • A proton (m = 1.67 × 10⁻²⁷ kg, q = 1.60 × 10⁻¹⁹ C) at 2.0 × 10⁶ m/s, at right angles to a 0.50 T field.
  • Radius: r = mv/(Bq) = (1.67 × 10⁻²⁷ × 2.0 × 10⁶) ÷ (0.50 × 1.60 × 10⁻¹⁹) = 0.042 m.
  • Period: T = 2πm/(Bq) = 1.3 × 10⁻⁷ s.
  • Double the field: r halves to 0.021 m, and T halves too, to 6.6 × 10⁻⁸ s.
Quick check
?A proton moves in a circular path of radius r in a uniform magnetic field, with its velocity perpendicular to the field. A second proton moves in the same field with twice the speed, its velocity also perpendicular to the field. Only magnetic forces are exerted on the protons. The radius of the second proton's circular path is kr. What is k?
Mission 4

Crossed fields

Velocity selector+−+−+−+−+−B into the pagefasterslowerv = E/BqEqvB+Curved paths sketched, not to scale.
  • In both E and B fields, a charge feels two independent forces: qE (any speed) and qvB (depends on speed).
  • E and B at right angles, both ⟂ to the beam, forces opposite. Straight through only if qE = qvB: v = E/B. This is a velocity selector.
  • Faster particles: magnetic force wins. Slower: electric force wins.
  • Example: plates 1.0 cm apart, 400 V, B = 0.050 T. E = 4.0 × 10⁴ V/m; v = E/B = 8.0 × 10⁵ m/s.
Quick check
?A proton moves at 2.0 × 10⁴ m/s toward the right side of the page through a region that contains a uniform electric field of magnitude 3.0 × 10³ N/C directed toward the bottom of the page and a uniform magnetic field of magnitude 0.050 T directed into the page. The gravitational force on the proton is negligible. What is the magnitude of the net force exerted on the proton at this instant? (Use e = 1.60 × 10⁻¹⁹ C.)
Mission 4

The Hall effect

Hall effectB out of the pageI−−−F+−+−+−+−+−+−VVHdElectrons drift opposite to I and are pushedto one edge: a potential difference acrossthe width.
  • Current flows along a thin slab in a field B ⟂ to its face. The moving charge carriers are pushed to one edge.
  • Charge builds up on opposite edges: a transverse potential difference, the Hall voltage VH.
  • It stops growing when the electric force balances the magnetic force: qE = qvB.
Quick check
A horizontal rectangular metal strip in the plane of the page, joined to wires at its left and right ends. An arrow labeIB
?The figure shows a metal strip, in the plane of the page, carrying a current I in a uniform magnetic field B. The charge carriers in the metal are electrons. As the magnetic field pushes on the moving electrons, charge builds up on two opposite surfaces of the strip. Which surface becomes negatively charged?
Mission check

?Two protons enter two separate regions at the same speed. Region 1 contains only a uniform electric field; region 2 contains only a uniform magnetic field. Each proton enters at right angles to the field lines. Gravity is negligible. A short time later, which statement is correct?
Mission 5Topics 12.1–12.3

Mission 5: Two parallel wires carry currents in the same direction. Do they attract or repel, and why?

Make a guess: Two parallel wires carry currents in the same direction. Do they attract or repel, and why?

Mission 5

Field of a long straight wire

Field of a long straight wirercurrent out of the pageB ∝ IB ∝ 1/rtwice as far: halfthe fieldr is measured fromthe wire’s axis, notits surfaceBr0B1/r0straightlinethrough 0Sketch graphs, no values.
  • B = μ0I/(2πr), r = distance from the wire's axis.
  • μ0 = 4π × 10⁻⁷ T·m/A: the permeability of free space, a constant.
  • B ∝ I and B ∝ 1/distance: twice as far, half the field.
  • Direction: right-hand rule. The field is tangent to circles around the wire.
Mission 5

Worked example

  • A long wire carries 15 A. Find B 3.0 cm from it.
  • B = μ0I/(2π × 0.030) = (4π × 10⁻⁷ × 15) ÷ (2π × 0.030).
  • Shortcut: μ0/2π = 2 × 10⁻⁷ T·m/A.
  • B = 2 × 10⁻⁷ × 15 ÷ 0.030 = 1.0 × 10⁻⁴ T.
  • About twice Earth's field at the surface (roughly 5 × 10⁻⁵ T): enough to swing a compass.
Quick check
?A long straight wire of diameter 0.010 m carries a current of 12 A. Point P is 0.045 m from the surface of the wire. What is the magnitude of the magnetic field produced by the wire at P? (Use μ0 = 4π × 10⁻⁷ T·m/A.)
Mission 5

Adding fields

Fields of two wires add as vectorsI2Iwire 1wire 2B = 0field of wire 1field of wire 2Between: opposite. Outside: same direction.Both currents out of the page. Field arrows toscale (proportional to current ÷ distance).
  • Fields from several wires add as vectors (superposition).
  • Find each field's size and direction separately, then add.
  • Two wires with currents in the same direction: between them the fields are opposite, and can cancel.
  • Currents in opposite directions: between them the fields add.
  • Loop center: every part of the loop gives a field in the same direction, along the axis.
Quick check
?Two long straight parallel wires, 1 and 2, are a distance d apart. Wire 1 carries a current I, and wire 2 carries a current 3I in the same direction. Point P is on the line joining the wires, between them, at the location where the net magnetic field produced by the two wires is zero. Ignore Earth's magnetic field. Which expression gives the distance from wire 1 to P?
Quick check
A dashed horizontal line with a proton (a circle marked +) on it and an arrow labeled v pointing to the right, parallel +vPQRddd
?A current is moving charge, so one moving proton makes a magnetic field too. Predict before the next screen. The figure shows a proton moving along the dashed line with velocity v, and three points P, Q and R, at the instant shown. BP, BQ and BR are the magnitudes of the magnetic field produced by the proton at these points at this instant. Which ranking is correct?
Mission 5

Field of one moving charge

Field of a moving proton+vB out of the pageB into the pageB = 0aheadB = 0behindBeside the charge: largest field. Straightahead or behind: zero.
  • A single moving charge produces a magnetic field. A charge at rest does not.
  • Larger speed → larger field. Greater distance → smaller field.
  • Direction: ⟂ to both the velocity and the line from the charge to the point. Right-hand rule as for a current (reverse it for a negative charge).
  • Largest beside the charge (line ⟂ to v); zero straight ahead or behind.
Mission 5

Force between parallel wires

Force between parallel wiresB1B2FFI1I2Same direction: attractB1B2FFI1I2Opposite directions: repelForce arrows equal in length (Newton’s thirdlaw).
  • Wire 1 makes a field at wire 2: B1 = μ0I1/(2πr), ⟂ to wire 2.
  • Wire 2 carries I2 in that field, so it feels F = I2ℓB1.
  • Same direction → attract. Opposite directions → repel.
Mission 5

Worked example

  • Two long parallel wires 5.0 cm apart each carry 10 A in the same direction.
  • Field of wire 1 at wire 2: B = 2 × 10⁻⁷ × 10 ÷ 0.050 = 4.0 × 10⁻⁵ T. Force per meter: BI = 4.0 × 10⁻⁵ × 10 = 4.0 × 10⁻⁴ N.
  • On 2.0 m of wire: 8.0 × 10⁻⁴ N, toward the other wire.
Quick check
?Two long straight parallel wires are 0.040 m apart. Wire 1 carries a current of 12 A, and wire 2 carries a current of 8.0 A in the opposite direction. What is the magnitude of the magnetic force exerted by wire 1 on a 1.5 m length of wire 2? (Use μ0 = 4π × 10⁻⁷ T·m/A.)
Quick check
?Two long straight parallel wires, X and Y, are 5.0 cm apart in air. X carries 2.0 A and Y carries 6.0 A, in the same direction. What is the magnetic force on a 1.0 m length of each wire?
Mission check

?A light, loosely wound coil of wire, like a soft spring, hangs vertically. A large steady current is passed through it. What happens to the length of the coil?
Mission 6Topic 12.4

Mission 6: Drop a strong magnet down a copper pipe and it falls in slow motion. Why?

Make a guess: Drop a strong magnet down a copper pipe and it falls in slow motion. Why?

Mission 6

Magnetic flux

Magnetic flux through a loopnormal along BΦB = BAθtiltedΦB = BA cos θplane along BΦB = 0Red arrow: area vector, at right angles tothe loop. θ is measured from the area vector,not from the plane.
  • Magnetic flux: how much field passes through an area. Think: number of field lines through it.
  • ΦB = BA cos θ, θ = angle between B and the area vector (⟂ to the surface).
  • Sign: positive if B is along the area vector, negative if opposite.
  • Unit: weber. 1 Wb = 1 T·m².
  • Plane of the loop parallel to the field: zero flux.
Quick check
?A square wire loop with sides of 0.20 m is in a uniform magnetic field of magnitude 0.40 T. The plane of the loop makes an angle of 30° with the direction of the field. What is the magnitude of the magnetic flux through the loop?
Mission 6

Faraday's law

Faraday's lawcenter-zero meterNSmoves influxtimeemftimeflat: emf = 0inheld stilloutemf = rate of change of flux: the slope ofthe flux graph.Sketch graphs; emf drawn as minus the slope(Lenz).
  • An emf is induced whenever the magnetic flux through the loop changes: move a magnet, move the loop, change B, change the area, or turn the loop.
  • Steady flux, however large: no emf.
  • Size: emf = rate of change of flux (× N for a coil of N turns).
  • |ε| = |ΔΦB/Δt|; with direction, ε = −ΔΦB/Δt.
  • On a ΦB–t graph for a single loop, |ε| = slope.
Mission 6

Worked example

  • A single loop of area 0.040 m² is ⟂ to a 0.50 T field. The field falls steadily to zero in 0.10 s.
  • ΔΦB = 0.50 × 0.040 = 0.020 T·m². |ε| = 0.020 ÷ 0.10 = 0.20 V.
  • Same change in 0.050 s: twice the emf. Once the field stops changing: zero.
Quick check
?A square wire loop with sides of 0.15 m lies in a horizontal plane in a uniform vertical magnetic field. The field's magnitude increases steadily from 0.20 T to 0.60 T in 0.12 s. What is the magnitude of the emf induced in the loop?
Mission 6

Lenz's law

Lenz's lawN pole pushed inNSNSmotionforce on magnetN pole pulled outSNNSmotionforce on magnetRed arrowheads: induced current on the nearside of each turn.
  • The induced current flows in the direction that opposes the change that produces it.
  • N pole pushed in: the near end of the coil becomes an N pole, repelling it.
  • N pole pulled out: the near end becomes an S pole, attracting it back.
  • The minus sign in Faraday's law expresses this.
  • Method: is the flux through the loop growing or shrinking? The induced field points against a growth, with a decrease. Then the right-hand rule gives the current.
Mission 6

Lenz's law is energy conservation

  • Suppose the induced current helped the change: the magnet would be pulled in faster, the current would grow, and so on. Energy from nothing.
  • So the induced current must oppose the motion. You must do work against that force.
  • That work becomes electrical energy, then thermal energy in the circuit.
  • Open circuit: an emf, but no current, so no opposing force.
  • A solid metal sheet or pipe acts like many loops: changing flux drives eddy currents around inside it, and they oppose the motion too.
Quick check
A square conducting loop drawn in the plane of the page, inside a larger dashed rectangle that marks a region of uniformIB into page
?The diagram shows a stationary square loop in the plane of the page, inside a region of uniform magnetic field directed into the page. The arrowheads show the direction of the current induced in the loop. Which change is taking place?
Mission check

?A thick aluminum plate swings as a pendulum through the gap between the poles of a strong magnet, and stops after a few swings. An identical plate with many deep slots cut into it swings for much longer. Which explains the difference?
Mission 7Topic 12.4

Mission 7: Move a metal rod or spin a coil near a magnet, and a voltage appears. What decides how big it is?

Make a guess: Move a metal rod or spin a coil near a magnet, and a voltage appears. What decides how big it is?

Mission 7

A moving rod makes an emf

A moving rod makes an emfB into the page+−velectronspushed downthe rodℓvΔtArea swept in Δt = ℓ × vΔtB, v and ℓ all at right angles
  • A rod moves at right angles to a uniform field. Its free electrons move with it, so the magnetic force pushes them along the rod.
  • Charge piles up at one end: an emf across the rod.
  • Flux view: in time Δt the rod sweeps area (length × vΔt), so the flux it cuts is B × length × vΔt.
  • ε = Bℓv (B, ℓ and v all at right angles).
  • Moving along the field, or along its own length: no emf.
Mission 7

Worked example: rod on rails

Rod on railsB into the pageRvIFInduced current: up the rod, down through R.Force on the rod: opposes v.
  • Rod 0.20 m long slides at 3.0 m/s on rails joined by a 1.5 Ω resistor. B = 0.50 T, at right angles to the rails' plane.
  • emf: 0.50 × 0.20 × 3.0 = 0.30 V.
  • Current: 0.30 ÷ 1.5 = 0.20 A (rod and rails of negligible resistance).
  • Force on the rod: B × I × length = 0.50 × 0.20 × 0.20 = 0.020 N, opposing its motion.
Quick check
?A metal rod slides at a constant 2.0 m/s along two parallel horizontal conducting rails that are 0.25 m apart. The rails are joined at one end by a 0.50 Ω resistor; the rod and rails have negligible resistance. A uniform 0.40 T magnetic field is perpendicular to the plane of the rails. At the instant the rod is 0.50 m from the resistor, what is the current in the resistor?
Quick check
?Use Lenz's law to predict before the next screen. A metal rod rests across two horizontal conducting rails that are joined at one end by a resistor, in a uniform vertical magnetic field. A student gives the rod a brief push along the rails and lets go. Friction and air resistance are negligible. Which claim about the rod's motion after the push, with its justification, is correct?
Mission 7

Why the rod is braked

  • The induced current is in the field, so the rod feels a force B × I × length.
  • Lenz's law: that force opposes the motion. Let go, and the rod slows down.
  • Constant speed needs a push equal to the magnetic force: F = IℓB = B²ℓ²v/R.
  • Energy: work done by the push = thermal energy in the resistor.
  • Example, the rod on rails above: 0.020 N × 3.0 m/s = 0.060 W = I²R = 0.20² × 1.5.
Mission check

?An aircraft with a wingspan of 40 m flies horizontally at 250 m/s. The vertical component of the Earth's magnetic field there is 4.0 × 10⁻⁵ T. What emf is induced between the wingtips?
Recap

The big ideas

Mission 1

  • Magnetic fields come from moving charges and magnets; field lines are closed loops, closer lines mean a stronger field.
  • Straight wire: circles, direction by the right-hand rule. Solenoid: uniform inside, bar-magnet pattern outside.
  • A compass aligns with the net field; Earth's field is roughly a dipole; there are no magnetic monopoles.

Mission 2

  • Magnetism comes from moving charges; a magnetized material has aligned atomic dipoles (domains in ferromagnets). Poles always come in pairs.
  • Ferromagnetic: strong, can stay aligned. Paramagnetic: weak, along the field, not kept. Diamagnetic: weak, opposite the field, in all materials. Permeability μ0 is constant; a material's μ is not.

Mission 3

  • Force on a current in a field: at right angles to both; zero when parallel.
  • Direction: right-hand rule.
  • FB = IℓB sin θ.

Mission 4

  • F = qvB sin θ.
  • The force is ⟂ to v, so speed and kinetic energy never change.
  • v ⟂ B gives a circle: r = mv/(Bq) = p/(Bq); the period does not depend on speed.
  • Crossed fields pass undeflected only particles with v = E/B.

Mission 5

  • Long straight wire: B = μ0I/(2πr); μ0 = 4π × 10⁻⁷ T·m/A.
  • Find B from one wire, then F = IℓB on the other.
  • Parallel wires: same direction attract, opposite repel; equal and opposite forces.

Mission 6

  • ΦB = BA cos θ; unit Wb = T·m².
  • Faraday: |ε| = |ΔΦB/Δt|; no change, no emf.
  • Lenz: the induced current opposes the change; otherwise energy would be created.

Mission 7

  • A rod on rails: ε = Bℓv; the magnetic force on the induced current opposes the motion.
🏆

Mini-lesson complete!

⭐⭐⭐

You've worked through Magnetism and Electromagnetism for AP Physics 2. 🎉

  1. Mission 1Switch on a current in a wire just above a compass. Which way does the needle turn, and why?
  2. Mission 2A magnet grabs an iron nail but ignores a copper pipe. What is different inside the iron?
  3. Mission 3A wire carrying a current lies between the poles of a magnet. Which way is it pushed?
  4. Mission 4A magnetic field can steer a beam of charged particles. Can it also make them go faster?
  5. Mission 5Two parallel wires carry currents in the same direction. Do they attract or repel, and why?
  6. Mission 6Drop a strong magnet down a copper pipe and it falls in slow motion. Why?
  7. Mission 7Move a metal rod or spin a coil near a magnet, and a voltage appears. What decides how big it is?

Your stars: 0 / 0

📣 Smashed it? Share your score

Challenge a friend to beat your stars, or show a parent how you got on.

→ Back to AP Physics 2