← A-Level Physics · CCEA · A-Level Physics revision
⭐ 0
CCEA A-level Physics (1210) · AS 1: Forces, Energy and Electricity (part 5)
Mini-Lesson

Forces, Energy and Electricity (part 5)

4 missions. Guess, learn, then check. Your place is saved.

  1. Mission 1A kettle's element gets very hot, yet the cable carrying the same current stays cool. Why?
  2. Mission 2One dead bulb can put out a whole string of lights, yet home lamps work on their own. Why?
  3. Mission 3Why do a car's headlights dim while its starter motor is turning?
  4. Mission 4A street lamp switches itself on at dusk. How does its circuit sense that it is getting dark?
Mission 1

Mission 1: A kettle's element gets very hot, yet the cable carrying the same current stays cool. Why?

Make a guess: A kettle's element gets very hot, yet the cable carrying the same current stays cool. Why?

Mission 1

Power: energy per second

Power: joules per second+−1 C1 C1 C1 C1 C1 C12 J per coulombtransferred here12 Vconventionalcurrentorange: carries energy · white: energygiven upV = 12 V: 12 J per coulombI = 3.0 A: 3.0 coulombs per second12 J C⁻¹ × 3.0 C s⁻¹ = 36 J s⁻¹P = IV = 36 W
  • Power = rate of energy transfer. 1 W = 1 J s⁻¹.
  • pd = joules per coulomb. Current = coulombs per second.
  • Multiply: joules per second.
  • P = IV.
  • Rearranged: V = P/I. (Also V = W/q: energy per unit charge.)
Mission 1

Three forms of one law

  • Use V = IR: P = IV = I²R = V²/R.
  • Same current (in series): use I²R. Larger R → more power.
  • Same pd (in parallel): use V²/R. Smaller R → more power.
Quick check
?The potential difference across an ohmic resistor is increased so that the current in the resistor becomes three times as large. What is the ratio of the new power dissipated in the resistor, P2, to the original power, P1?
Mission 1

Energy transferred

  • Energy = power × time = IVt.
  • A heater on 12 V takes 3.0 A for 5.0 minutes.
  • P = 12 × 3.0 = 36 W. t = 5.0 × 60 = 300 s.
  • Energy = 36 × 300 = 1.1 × 10⁴ J.
  • Check: R = 12 ÷ 3.0 = 4.0 Ω; I²R = 3.0² × 4.0 = 36 W.
Quick check
?A steady current of 0.25 A flows in a 24 Ω resistor for 2.0 minutes. How much energy is dissipated in the resistor?
Mission 1

The heating effect

Kettle element and cablesupplyelement (large R)cable (tiny R)same IeverywherePower dissipated, P = I²R (same I)elementcabletinyBar lengths are qualitative.
  • Electrons collide with the lattice ions and pass on energy. The ions vibrate more: the resistor heats up.
  • Kettle element and its cable are in series: the same current.
  • P = I²R: the element's resistance is far larger, so nearly all the power is dissipated there.
  • The cable's resistance is tiny: very little heating.
  • Wanted heating: kettles, heaters. Unwanted: cables, chargers.
Quick check
?A 60 W lamp and a 100 W lamp are both designed to work on the same 230 V supply. Which lamp has the larger resistance when working normally, and why?
Mission check

?A 60 W lamp and a 100 W lamp are both rated for a 230 V supply. They are connected in series across a 230 V supply. Assume each keeps its normal working resistance. Which lamp is brighter?
Mission 2

Mission 2: One dead bulb can put out a whole string of lights, yet home lamps work on their own. Why?

Make a guess: One dead bulb can put out a whole string of lights, yet home lamps work on their own. Why?

Mission 2

Closed, open, short

Closed, open and short circuits(a) closed+lamp lit(b) open+no current(c) short circuit+lamp: no currentArrows: conventional current, + to −.Symbol keycellbatteryresistorswitch (open)variable resistorAammeterlampVvoltmeter
  • Charge flows only round a closed loop.
  • A gap anywhere in a loop (open circuit): no current in that loop.
  • Short circuit: a wire straight across a component. No potential difference across it, so no current through it.
Mission 2

Circuit diagrams

  • A circuit diagram shows what connects to what, not where things sit.
  • Conventional current flows from + to − round the external circuit.
  • A diagonal arrow through a symbol = variable component.
  • Ideal wires have no resistance. An ideal cell has no internal resistance.
Quick check
?Three circuits are each made from an identical cell of negligible internal resistance, a resistor and a lamp. In circuit 1 the three form a single closed loop. Circuit 2 is the same loop with an open switch added. Circuit 3 is the same loop as circuit 1 with a wire of negligible resistance connected directly across the lamp's terminals. Which ranks the currents I1, I2 and I3 in the lamps of circuits 1, 2 and 3?
Mission 2

Two conservation laws

Junction and loop3 A in2 A out1 A outin = out: 3 = 2 + 16 V2 V4 V+loop: 6 = 2 + 4
  • Junction: total current in = total current out. Charge is conserved: none piles up.
  • Closed loop: sum of emfs = sum of potential differences. Energy is conserved: each coulomb gains in the cell what it loses in the components.
  • Current is not used up. Energy is transferred.
Quick check
?A 9.0 V supply of negligible internal resistance is connected to three resistors in series. The potential differences across two of them are 2.0 V and 4.5 V. What is the potential difference across the third resistor?
Mission 2

Series and parallel

Series and parallelSeriesIIIIV₁V₂VSame current I everywhere. V = V₁ + V₂ParallelII₁I₂VVVSame V across each branch. I = I₁ + I₂string of lights: serieshouse lamps: parallelone pathfull supply pd each
  • Series: one path. Same current everywhere. pds add: V = V1 + V2.
  • Parallel: separate branches. Same pd across each. Currents add: I = I1 + I2.
  • Series: R = R1 + R2 + … Parallel: 1/R = 1/R1 + 1/R2 + …
  • Parallel: more paths, so the total is less than the smallest branch resistance.
  • Home lamps are in parallel: each has the full supply potential difference, whatever the others do.
Mission 2

Where the formulas come from

  • Series, same I. Energy: V = V1 + V2.
  • So IR = IR1 + IR2 → R = R1 + R2.
  • Parallel, same V. Charge: I = I1 + I2.
  • So V/R = V/R1 + V/R2 → 1/R = 1/R1 + 1/R2.
Quick check
?Resistors of 3.0 Ω, 6.0 Ω and 8.0 Ω are connected in parallel. What is the equivalent resistance of the combination?
Mission 2

Worked example

Worked example circuit6.0 V1.0 Ω2.0 V3.0 Ω4.0 V6.0 Ω4.0 V2.0 A1.3 A0.67 A2.0 V + 4.0 V = 6.0 V1.3 A + 0.67 A = 2.0 A
  • 6.0 V supply, negligible internal resistance. A 1.0 Ω resistor in series with 3.0 Ω and 6.0 Ω in parallel.
  • Parallel pair: 1/R = 1/3.0 + 1/6.0 → 2.0 Ω.
  • Total: 1.0 + 2.0 = 3.0 Ω. Supply current: 6.0 ÷ 3.0 = 2.0 A.
  • Potential difference across the pair: 2.0 × 2.0 = 4.0 V. Across the 1.0 Ω: 2.0 V. Sum: 6.0 V.
  • Branch currents: 4.0 ÷ 3.0 = 1.3 A; 4.0 ÷ 6.0 = 0.67 A. Sum: 2.0 A.
Mission 2

Meters

Connecting metersAVammeter: in serieslampvoltmeter: across the lampIdeal ammeter: zero resistance.Ideal voltmeter: infinite resistance.
  • Ammeter: in series. Ideal: zero resistance, so it does not change the current.
  • Voltmeter: in parallel, across the component. Ideal: infinite resistance, so it draws no current.
  • Treat meters as ideal unless told otherwise.
  • Real meters change the circuit a little: a real ammeter adds resistance; a real voltmeter draws some current.
Quick check
?A student wants to measure the current in a lamp and the pd across it, but connects the meters the wrong way round. The circuit is: a cell, a voltmeter and the lamp connected in series in a single loop, with an ammeter connected in parallel with the lamp. Both meters are ideal. What does the student observe?
Mission 2

Testing the rules: practical

Testing the series and parallel rulesSeriesAR₁AR₂VVBoth ammeters read the same. Voltmeterreadings add up to the supply pd.ParallelAAR₁AR₂Same pd across each branch. Branch currentsadd up to the supply current.
  • Series test: ammeters before, between and after the resistors; a voltmeter across each resistor and one across the supply.
  • Compare: do the ammeters agree? Do the resistor pds add up to the supply pd?
  • Parallel test: an ammeter in each branch and one in the supply lead; a voltmeter across each branch.
  • Compare: are the branch pds equal? Do the branch currents add up to the supply current?
  • Find V/I for each combination. Compare with R1 + R2 (series) and (1/R1 + 1/R2)⁻¹ (parallel).
  • Readings agree within meter uncertainty? The rules are confirmed.
Quick check
?In the series test, a student puts ammeters before and after two resistors: they read 0.25 A and 0.24 A. Voltmeters across the resistors read 2.1 V and 3.8 V, and across the supply 6.0 V. Which is the best conclusion?
Mission check

?Three identical lamps are connected to a supply of negligible internal resistance: lamp A is in series with lamps B and C, which are in parallel with each other. The filament of lamp C breaks. What happens to the brightness of lamps A and B? (Assume each lamp's resistance stays the same.)
Mission 3

Mission 3: Why do a car's headlights dim while its starter motor is turning?

Make a guess: Why do a car's headlights dim while its starter motor is turning?

Mission 3

emf and internal resistance

A real cellreal cell (dashed box)+−emf 1.5 Vr = 0.50 ΩR = 2.5 ΩI = 0.50 AVreads the terminal pd: 1.25 VEnergy per coulomb (J C⁻¹ = V)gained: emf 1.5terminal pd 1.25 (outside)lost volts Ir = 0.25 (inside r)
  • emf: energy transferred to each coulomb of charge by the source.
  • A real cell has internal resistance r. Model: an ideal cell in series with r.
  • With a current, some energy per coulomb is dissipated inside the cell. That pd is the lost volts, Ir.
  • Terminal pd = emf − lost volts.
Mission 3

Terminal potential difference

  • V = E − Ir, with V the terminal pd.
  • No current: terminal pd = emf.
Quick check
?A battery with an internal resistance of 0.50 Ω drives a current of 0.60 A through a lamp, and an ideal voltmeter across the battery's terminals reads 4.2 V. The lamp is then disconnected, so that only the voltmeter remains connected across the battery. What does the voltmeter now read?
Mission 3

Worked example

  • Cell: emf 1.5 V, internal resistance 0.50 Ω. External resistor: 2.5 Ω.
  • Current = emf ÷ total resistance = 1.5 ÷ (2.5 + 0.50) = 0.50 A.
  • Lost volts = Ir = 0.50 × 0.50 = 0.25 V.
  • Terminal pd = 1.5 − 0.25 = 1.25 V.
  • Check: IR = 0.50 × 2.5 = 1.25 V.
Quick check
?A battery of emf 9.0 V and internal resistance 0.50 Ω is connected to a 4.0 Ω resistor. What is the terminal potential difference of the battery?
Mission 3

Consequences

Starter motor and headlightsheadlightsMswitchstarter motorrcar batteryTerminal pdopenclosedlights dimSwitch closed: large motor current, morelost volts.Bar lengths are qualitative.
  • More current → more lost volts → lower terminal pd.
  • A starter motor draws a very large current. The battery's terminal pd drops, so the headlights dim.
  • Short circuit (R = 0): current = emf ÷ r. Small r → a very large current; the cell heats up.
  • Car batteries need a small r to deliver large currents. High-voltage lab supplies have a large r so the current stays safe.
Quick check
?Cells P and Q have the same emf. P has a smaller internal resistance than Q. Each cell is connected in turn to the same lamp. Which statement is correct?
Mission 3

Measuring emf and r

Measuring emf and r+−Aswitchvariable resistorVacross the cellV / VI / A0intercept = emfgradient = −rV = −rI + emfSketch, no data.
  • Cell, variable resistor and ammeter in series. Voltmeter across the cell's terminals.
  • Change the resistance: record terminal pd V and current I each time.
  • V = −rI + emf: plot V against I. Straight line.
  • y-intercept = emf. Gradient = −r.
  • Switch off between readings: a warm cell's r changes.
  • This is a required practical.
Quick check
Graph of terminal pd V / V on the vertical axis (ticks at 0.5, 1.0, 1.5) against current I / A on the horizontal axis (tI / AV / V0.51.01.52.02.50.51.01.5
?The graph shows how the terminal pd V of a cell varies with the current I that it delivers. What is the internal resistance of the cell?
Mission check

?A battery of internal resistance r is connected to an external resistor whose resistance equals r. The external resistor is then replaced by one of resistance 2r. How does the potential difference across the terminals of the battery change?
Mission 4

Mission 4: A street lamp switches itself on at dusk. How does its circuit sense that it is getting dark?

Make a guess: A street lamp switches itself on at dusk. How does its circuit sense that it is getting dark?

Mission 4

Sharing a pd

Potential divider+−VinR₂R₁IIVoutSame current I in both. Vout is the pdacross R₁ only.
  • Two resistors in series across a supply Vin carry the same current.
  • So the pd splits in proportion to resistance. Bigger R, bigger share.
  • Vout = R1Vin/(R1 + R2), with Vout taken across R1.
  • V1/V2 = R1/R2.
Mission 4

Worked example

  • 12 V supply, negligible internal resistance. R1 = 3.3 kΩ, R2 = 2.2 kΩ. Find the pd across R1.
  • Vout = 3.3 × 12/(3.3 + 2.2) = 7.2 V.
  • The pd across R2 is 12 − 7.2 = 4.8 V. Ratio 7.2 : 4.8 = 3.3 : 2.2.
Quick check
?An LDR and a 300 Ω resistor are in series across a 6.0 V supply of negligible internal resistance. In the room's light the LDR's resistance is 900 Ω. What does an ideal voltmeter across the 300 Ω resistor read?
Mission 4

Potentiometer

Potentiometer+−Vinuniform tracksliding contactABVreads the pd between A andthe sliderUniform track: pd from A ∝ distance from AVin0pdABdistance from A
  • A resistance track across the supply, with a sliding contact.
  • Output between one end and the slider: any pd from 0 to Vin.
  • Uniform track: pd ∝ length from that end.
  • A divider gives a variable pd from a fixed supply.
Quick check
?A potentiometer has a uniform resistance track connected across a 9.0 V dc supply of negligible internal resistance. An ideal voltmeter is connected between one end of the track and the sliding contact, which is one third of the way along the track from that end. What does the voltmeter read?
Mission 4

Sensors in a divider

Thermistor and LDRNTC thermistorLDRresistancetemperaturefalls as it warmsresistancelight intensityfalls in brighterlightSketch graphs, no scale.
  • NTC thermistor: R falls as temperature rises.
  • LDR: R falls as light gets brighter.
  • Put one in a divider: when its R changes, its share of the pd changes.
  • A component's pd rises when its share of the total R rises.
Mission 4

Control circuits

Sensing circuits(a) Dusk lamp: Vout across the LDR+−VinvariableLDRVoutswitchingcircuitlampDarker → LDR's R up → Vout up → lamp on.(b) Heating: Vout across the thermistor+−VinvariablethermistorVoutswitchingcircuitheaterColder → thermistor's R up → Vout up →heater on.
  • Dusk lamp: Vout across the LDR. Darker → LDR's R up → Vout up → switches the lamp on.
  • Heating control: Vout across the thermistor. Colder → R up → Vout up → switches the heater on.
  • Make the fixed resistor variable to set the switching point.
  • Vout goes to a switching circuit, not straight to the lamp or heater.
Quick check
?An LDR and a 10 kΩ fixed resistor are in series across a 6.0 V supply of negligible internal resistance. An ideal voltmeter is connected across the fixed resistor. The LDR's resistance is 50 kΩ in the dark and 1.0 kΩ in bright light. What does the voltmeter read in each case?
Mission 4

Loaded divider

Loaded dividerNo load+−12 VR₂10 kΩR₁10 kΩVout = 6.0 VLoad RL across R₁+−12 VR₂10 kΩR₁10 kΩRL10 kΩVout = 4.0 VRL is in parallel with R₁: the pair is5.0 kΩ, so Vout falls.
  • Vout is across R1. Connect a load RL across R1. It is in parallel with R1.
  • The parallel pair has less resistance than R1, so Vout falls.
  • Calculate: replace R1 by R1RL/(R1 + RL), then use Vout = R1Vin/(R1 + R2).
  • 12 V, R1 = R2 = 10 kΩ: unloaded Vout = 6.0 V. With a 10 kΩ load: pair = 5.0 kΩ, Vout = 12 × 5.0/15 = 4.0 V.
  • Keep RL much larger than R1 and Vout hardly changes.
Quick check
?A 9.0 V supply of negligible internal resistance is connected across R1 = 6.0 kΩ in series with R2 = 3.0 kΩ. A 3.0 kΩ load is connected across R1. What is the pd across the load?
Mission check

?An NTC thermistor and a fixed resistor are in series across a supply of constant pd. An ideal voltmeter is connected across the thermistor. The thermistor is warmed. What happens to the voltmeter reading?
Recap

The big ideas

Mission 1

  • P = IV = I²R = V²/R; energy = IVt. Same current: larger R, more power. Same pd: smaller R, more power.
  • V = P/I.

Mission 2

  • Junction: current in = current out (charge). Loop: emfs = sum of potential differences (energy).
  • Series: same I, pds add, R = R1 + R2. Parallel: same V, currents add, 1/R = 1/R1 + 1/R2.
  • Ideal ammeter: zero resistance, in series. Ideal voltmeter: infinite resistance, in parallel.
  • Required task: meter readings confirm the series and parallel rules within uncertainty.

Mission 3

  • V = E − Ir.
  • Graph of V against I: intercept = emf, gradient = −r.

Mission 4

  • Vout = R1Vin/(R1 + R2): series resistors share the pd in proportion to resistance.
  • Thermistor or LDR in a divider: its share of the pd changes with temperature or light.
  • A load in parallel with R1 (the output resistor) lowers Vout.
🏆

Mini-lesson complete!

⭐⭐⭐

You've worked through Forces, Energy and Electricity (part 5) for CCEA A-level Physics. 🎉

  1. Mission 1A kettle's element gets very hot, yet the cable carrying the same current stays cool. Why?
  2. Mission 2One dead bulb can put out a whole string of lights, yet home lamps work on their own. Why?
  3. Mission 3Why do a car's headlights dim while its starter motor is turning?
  4. Mission 4A street lamp switches itself on at dusk. How does its circuit sense that it is getting dark?

Your stars: 0 / 0

📣 Smashed it? Share your score

Challenge a friend to beat your stars, or show a parent how you got on.

→ Back to A-Level Physics · CCEA