← A-Level Physics · CCEA · A-Level Physics revision
⭐ 0
CCEA A-level Physics (1210) · AS 1: Forces, Energy and Electricity (part 4)
Mini-Lesson

Forces, Energy and Electricity (part 4)

6 missions. Guess, learn, then check. Your place is saved.

  1. Mission 1A lamp glows while charge flows through it. Does any of the charge get used up on the way?
  2. Mission 2A battery is marked one and a half volts, a lamp six. What exactly does a volt count?
  3. Mission 3Double the potential difference across a wire. When does the current exactly double?
  4. Mission 4Heat a metal wire and its resistance rises. Heat a thermistor and it falls. Why the difference?
  5. Mission 5Stretch a metal wire to twice its length. What happens to its resistance?
  6. Mission 6A ruler, a micrometer, an ammeter and a voltmeter. How can they tell you what a wire is made of?
Mission 1

Mission 1: A lamp glows while charge flows through it. Does any of the charge get used up on the way?

Make a guess: A lamp glows while charge flows through it. Does any of the charge get used up on the way?

Mission 1

Charge and current

Charge flowing past a cross-sectioncross-sectionflow of chargecharge Q crosses in time tcurrent = rate of flow of charge
  • Charge, Q, in coulombs (C). One electron: −e, with e = 1.60 × 10⁻¹⁹ C: tiny.
  • 1 C is the charge of about 6.25 × 10¹⁸ electrons.
  • Current: the rate of flow of charge through a cross-section.
  • I = Q/t
  • 1 A = 1 C s⁻¹. So 1 C is the charge passing a point when 1 A flows for 1 s.
Mission 1

Worked example

  • A charger supplies a steady 1.5 A for 20 minutes.
  • Δt = 20 × 60 = 1200 s.
  • ΔQ = IΔt = 1.5 × 1200 = 1800 C.
  • Number of electrons = 1800 ÷ (1.60 × 10⁻¹⁹) = 1.1 × 10²².
Quick check
?In an electron beam in a vacuum tube, 1.5 × 10¹⁵ electrons pass through a cross-section of the beam in 8.0 s at a steady rate. What is the magnitude of the current in the beam? Use e = 1.60 × 10⁻¹⁹ C.
Mission 1

What actually moves

Charge carriers in a metalno pd: random motion, no net flow+++++++++++++++++++++pd applied: the same motion plus a slow drift++++++++++++++++++++++−random motion: fastdrift: slow (net)
  • Metals: free electrons, already present throughout the wire.
  • No cell connected: carriers move fast but randomly. Net flow through any cross-section: zero, so no current.
  • Connect a cell: the carriers already in the wire start to drift. The cell does not supply the charge.
Quick check
?Predict first. A copper wire forms part of a circuit carrying a steady direct current. Which statement about the charge carriers in the wire is correct?
Mission 1

Which way is the current?

Conventional current and electron flow+−conventional current: + to −electronsin the cell: − to +
  • Conventional current: the direction positive charge would move. Outside the cell: from + to −.
  • In metals, electrons move the opposite way.
Mission 1

Charge is conserved

Charge is conservedAA0.50 A0.50 Asame current in and outArrows: conventional current.
  • Charge cannot be created, destroyed or used up.
  • In a steady current, charge cannot build up anywhere.
  • So the current into a lamp equals the current out of it. Same all round a single loop.
  • The lamp transfers energy, not charge.
Mission check

?A copper wire has a thick section X joined to a thin section Y, and there is a steady current in the wire. How do the currents IX and IY in the two sections compare?
Mission 2

Mission 2: A battery is marked one and a half volts, a lamp six. What exactly does a volt count?

Make a guess: A battery is marked one and a half volts, a lamp six. What exactly does a volt count?

Mission 2

Potential difference

Joules per coulombV6.0 V+−6 J0 J6 J0 J6 J0 Jinto the lamp: 6 J per coulombout of the lamp: 0 J of that energylampeach circle: 1 C of charge6 J per coulomb = 6.0 V across the lamp
  • Potential difference (pd) between two points: the work done (energy transferred) per unit charge moving between them.
  • V = W/q
  • 1 volt = 1 J C⁻¹: 1 J transferred for each coulomb passing between the points.
  • Also V = P/I (P: power).
Mission 2

Energy in a lamp

Energy transferred in a lamp3.0 C in3.0 C out18 J leaves the circuitas light and internal energy6.0 V across the lamp
  • Charge passing through a lamp or resistor transfers electrical energy to internal energy and light.
  • The charge comes out; the energy stays behind.
  • Worked example: potential difference across a lamp 6.0 V; 3.0 C passes through.
  • W = Vq = 6.0 × 3.0 = 18 J transferred in the lamp.
Quick check
?A steady current of 0.50 A flows through a small electric motor for 2.0 minutes. In this time, 360 J of energy is transferred from electrical energy to other forms in the motor. What is the potential difference across the motor?
Quick check
?Predict first. A cell has an emf of 1.5 V. What does this mean?
Mission 2

Electromotive force (emf)

Emf: work done on the charge in the source+−+++Inside the cell:conventional currentflows from − to +.Charge is "lifted":chemical energy→ electrical energyOutside: + to −round the circuit.
  • A cell or supply does work on the charge: energy from another store (chemical, light) becomes electrical energy.
  • emf: energy transferred to electrical energy per unit charge passing through the source.
  • Symbol E.
  • emf is measured in volts, like potential difference. It is not a force.
Mission 2

emf or pd?

Emf or pd?emfin the sourcecellother formselectricalpdin a componentlamp, resistor, motorelectricalother formsJ C⁻¹ = VJ C⁻¹ = VRound a circuit: energy given to the charge= energy given up by the charge.
  • emf: other forms → electrical energy. Happens in the source.
  • pd: electrical energy → other forms. Happens in components (lamps, resistors, motors).
  • Both: energy per unit charge, in J C⁻¹ = V.
  • Round a complete circuit, all the energy the source gives each coulomb is transferred in the components.
Mission 2

Where emf comes from

Where emf comes from+−+−+−+−+−chemical cellreactions separate+ and − chargechemical → electrical
  • Chemical cell: reactions push positive and negative charge apart, to opposite terminals. Chemical energy → electrical.
  • A cell does not store charge or make new charge. It gives energy to charge that is already in the circuit.
Mission check

?A battery of emf 12 V drives a steady current of 40 A through a starter motor for 1.5 s. How much energy does the battery transfer to the charge that passes through it in this time?
Mission 3

Mission 3: Double the potential difference across a wire. When does the current exactly double?

Make a guess: Double the potential difference across a wire. When does the current exactly double?

Mission 3

Resistance

Same pd, two resistors6.0 VA1.2 A5.0 Ω6.0 VA0.60 A10 ΩSame pd: double R, half the current.
  • Resistance: how strongly a component opposes the flow of charge.
  • R = V/I: the pd across it ÷ the current through it.
  • Unit: the ohm, 1 Ω = 1 V A⁻¹.
  • Same potential difference: bigger R → smaller current.
Quick check
?Predict first. What is the origin of the electrical resistance of a metal wire?
Mission 3

Where resistance comes from

Electron collisions in a metal++++++++++++++++++−electric field Eelectron driftRed: an ion hit by the electron vibratesmore. Its energy heats the wire.Schematic, not to scale. Real drift is farslower than the speed between collisions.
  • The potential difference sets up an electric field in the wire. Free electrons are accelerated by it (opposite to the field: they are negative)…
  • …then collide with the vibrating positive ions of the lattice, giving them energy.
  • Speed up, collide, speed up again: a steady average drift.
  • Ions gain energy → vibrate more → the conductor warms: the heating effect of a current.
  • The energy comes from the charges' electrical energy. No charge is used up.
Mission 3

Ohm's law

Ohmic I–V graphI / AV / V0ΔVΔIgradient = ΔI ÷ ΔV= 1/Rreversedpd: same line
  • Ohm's law: the current in a metallic conductor is proportional to the pd across it, provided its temperature (and other physical conditions) stays constant.
  • Ohmic I–V graph: a straight line through the origin, same in both directions.
  • R = V/I defines resistance for any component, at any point. Ohm's law is the special case where R stays constant.
Mission 3

Worked example: is it ohmic?

  • Readings: 2.0 V, 0.40 A and 6.0 V, 1.2 A.
  • R = V/I: 2.0 ÷ 0.40 = 5.0 Ω; 6.0 ÷ 1.2 = 5.0 Ω. Same → consistent with ohmic.
  • Graph of I (vertical) against V (horizontal): gradient = 1.2 ÷ 6.0 = 0.20 A V⁻¹ = 1/R.
  • With V on the vertical axis, the gradient is R itself.
Quick check
?The I–V characteristic of a filament lamp is plotted with current I on the vertical axis and pd V on the horizontal axis. Up to 0.10 V the graph is a straight line through the origin, and at 0.10 V the current is 0.050 A. At 6.0 V the current is 0.50 A, and the tangent to the curve at this point has a gradient of 0.040 A V⁻¹. What is the resistance of the lamp at 6.0 V, and how is it found?
Mission 3

The filament lamp

Filament lamp I–V graphI / AV / V0Ptangent: not RR at P = V/I(line from the origin)dashed: metal wire atconstant temperatureEqual steps in V give smaller steps in I.Sketch: shapes only, no data.
  • I–V graph: through the origin, curving towards the V axis; the same shape for reversed pd.
  • Larger current → filament hotter → ions vibrate more → more collisions → R rises.
  • So equal steps in V give smaller and smaller steps in I. Non-ohmic.
  • Resistance at a point = V/I at that point. Not the gradient of the tangent.
  • A metal wire kept at constant temperature: a straight line. Same metal, different temperature behaviour.
Quick check
?A student investigates whether a length of metal wire obeys Ohm's law. At the highest currents, V/I is clearly larger than at low currents. What is the best change to the method?
Mission 3

Practical: measuring an I–V characteristic

I–V characteristic circuit+−supplypotential dividerAcomponentVin seriesacross thecomponent only
  • Ammeter in series with the component; voltmeter in parallel across it.
  • Vary the pd with a potential divider (or variable resistor). Take readings in steps.
  • Reverse the component (or supply) for negative values.
  • Wire: keep the current small (or the wire in a water bath) so its temperature stays constant.
  • Lamp: let each reading settle before recording.
  • Resistance can also be read directly with a multimeter on its ohms range (component out of the powered circuit).
Mission 3

Reading your results

  • Plot I (vertical) against V.
  • Wire at constant temperature: straight line through the origin → ohmic; R = 1/gradient.
  • Filament lamp: curve bending towards the V axis → R = V/I rises with current.
  • Find R at any point from V/I, not from the tangent.
Mission check

?Three components X, Y and Z are tested. The currents at pds of 1.0 V, 2.0 V and 4.0 V are: X — 0.10 A, 0.20 A, 0.40 A; Y — 0.05 A, 0.15 A, 0.35 A; Z — 0.20 A, 0.30 A, 0.40 A. Which of the components are ohmic, and why?
Mission 4

Mission 4: Heat a metal wire and its resistance rises. Heat a thermistor and it falls. Why the difference?

Make a guess: Heat a metal wire and its resistance rises. Heat a thermistor and it falls. Why the difference?

Mission 4

The semiconductor diode

Diode current–voltage graphIV / V≈ 0.6 Vthresholdsteep risereverse:tiny currentdiode: conducts this way →Resistance = V/I at each point: very highbelow the threshold, low above it. Sketch(silicon diode).
  • A diode lets current through in one direction only.
  • Forward bias: almost no current until the pd reaches the threshold (≈ 0.6 V for silicon). Then the current rises steeply.
  • Reverse bias: a tiny current: very high resistance.
  • Resistance = V/I at each point: very high below threshold, low above it.
Quick check
?The pd across a forward-biased silicon diode is raised from 0.2 V to 0.8 V. What happens to its resistance?
Mission 4

The NTC thermistor

NTC thermistor graphsNTC thermistorresistancetemperaturefalls steeply,then less steeplyIVcurves towards the I axisTemperature up → resistance down. A largercurrent heats it, R falls, so I rises fasterthan V. Sketches, no values.
  • NTC: negative temperature coefficient. Temperature up → resistance down.
  • R–T graph: falls steeply at low temperatures, then less steeply. Not a straight line.
  • I–V graph: curves upwards (towards the I axis, I vertical). A larger current heats it, R falls, so I rises faster than V.
  • Use: temperature sensor, e.g. in a potential divider.
Mission 4

Metal or thermistor: why opposite?

Why a metal and a thermistor respond oppositelyMetalNTC thermistor(semiconductor)coldwarmmore vibration;carriers: hardly changemore vibration;many more carriersR ↑R ↓Blue: ions (vibrating). Yellow: chargecarriers; orange: carriers freed by warming.
  • Two effects of warming:
    • ions vibrate more → more collisions → R up;
    • more charge carriers freed → R down.
  • Metal: carrier number (n) hardly changes. Collisions win → R rises (roughly in proportion to temperature rise).
  • NTC thermistor (semiconductor): n rises hugely. Carriers win → R falls.
Quick check
?A copper wire has a fixed pd across it. As it warms up, the current falls. A student explains: "Warming reduces the number of free electrons in the copper." Which correction is right?
Mission 4

Practical: R against temperature for an NTC thermistor

Measuring a thermistor’s resistance against temperatureΩmultimeteron ohmswaterheaterstirrerthermometerthermistor, sealedin a test tubebulb beside itHeat in steps; stir; wait for steadyreadings; record R and temperature. Plot Ragainst temperature.
  • Thermistor sealed in a test tube (or waterproofed) in a water bath, with a thermometer beside it.
  • Measure R with a multimeter (ohms range), or with an ammeter and voltmeter using a small current (avoid self-heating).
  • Heat the water in steps (e.g. from ice-water to ≈ 90 °C). Stir, wait for steady readings, record R and θ.
  • Plot R against θ: a curve falling steeply, then less steeply.
Mission check

?An NTC thermistor senses the temperature inside a fridge. After the door is closed, the thermistor cools from 15 °C to 5 °C. What happens to its resistance, and why?
Mission 5

Mission 5: Stretch a metal wire to twice its length. What happens to its resistance?

Make a guess: Stretch a metal wire to twice its length. What happens to its resistance?

Mission 5

Resistivity

Length, area and resistanceReferencelength, area ARTwice as long2 × length, area A2RTwice the arealength, area 2AR/2Same shading: same material, same ρ.
  • Longer wire → more collisions in the way: R ∝ length.
  • Thicker wire → more paths side by side: R ∝ 1/A.
  • R = ρl/A.
  • Resistivity ρ depends only on the material (and its temperature), not on its shape.
  • Unit: Ω m.
  • Definition: ρ = RA/l. Resistivity is numerically equal to the resistance of a sample of the material 1 m long with a cross-sectional area of 1 m².
  • Copper: 1.7 × 10⁻⁸ Ω m. Constantan: 4.9 × 10⁻⁷ Ω m.
Quick check
?A uniform copper wire is cut into two pieces of equal length. How do the resistance and the resistivity of one piece compare with those of the original wire?
Mission 5

Worked example

  • Constantan wire: length 0.80 m, diameter 0.30 mm, ρ = 4.9 × 10⁻⁷ Ω m. Find R.
  • Radius = 0.15 mm = 1.5 × 10⁻⁴ m. Halve the diameter first.
  • A = πr² = π × (1.5 × 10⁻⁴)² = 7.07 × 10⁻⁸ m².
  • R = ρ × length ÷ A = (4.9 × 10⁻⁷ × 0.80) ÷ (7.07 × 10⁻⁸) = 5.5 Ω.
  • Trap: 1 mm² = 10⁻⁶ m², not 10⁻³ m².
  • Stretch a wire to twice the length: its volume is unchanged, so A halves. The resistance becomes 2 ÷ ½ = 4 times as large.
Quick check
?A copper cable has length 5.0 m and diameter 1.0 mm. The resistivity of copper is 1.7 × 10⁻⁸ Ω m. What is the resistance of the cable?
Mission 5

Resistance against length

Resistance against lengthR / Ωlength / m0ΔlengthΔRgradient = ρ/Aso ρ = gradient × A
  • Same wire, different lengths: R against length is a straight line through the origin.
  • Gradient = R ÷ length = ρ/A.
  • So ρ = gradient × A.
  • Unit check: Ω m⁻¹ × m² = Ω m.
Mission check

?Wire X has resistance R and is made of a material of resistivity ρ. Wire Y is made of the same material at the same temperature, but it is half as long as X and has half the diameter of X. What are the resistance and the resistivity of wire Y?
Mission 6

Mission 6: A ruler, a micrometer, an ammeter and a voltmeter. How can they tell you what a wire is made of?

Make a guess: A ruler, a micrometer, an ammeter and a voltmeter. How can they tell you what a wire is made of?

Mission 6

Measuring resistivity

Measuring resistivity0metre rulefixed clipsliding cliplength LAVMicrometer: diameter at several points,turning the wirewireA = πd²/4with the mean d
  • Wire taped along a metre rule. A sliding crocodile clip sets the length.
  • Micrometer: measure the diameter at several points, turning the wire each time. Use the mean d.
  • A = πd²/4.
  • Ammeter in series, voltmeter across that length: R = V/I.
  • Repeat for at least six lengths.
Mission 6

From readings to ρ

  • Plot R against length. Gradient = ρ/A, so ρ = gradient × A.
  • Contact resistance at the clips shifts the line up. It does not change the gradient.
  • Keep the current small and switch off between readings: a warm wire has a larger ρ.
  • Check the micrometer for zero error.
  • Example: gradient 4.3 Ω m⁻¹, d = 0.38 mm → A = 1.13 × 10⁻⁷ m² → ρ = 4.9 × 10⁻⁷ Ω m.
Quick check
?A student plots R against length for a uniform wire of diameter 0.40 mm. The best-fit line has a gradient of 4.0 Ω m⁻¹ and crosses the R axis at 0.30 Ω. What is the resistivity of the wire?
Quick check
?A wire has a resistance of 4.0 Ω per metre, and the clips add a constant 0.50 Ω to every reading. A student finds the resistivity from a single reading at a length of 0.50 m, rather than from the gradient of a graph. How does her value compare with the true value?
Mission 6

Superconductivity

The superconducting transitionresistivitytemperature / K077nitrogenboilscriticaltemperaturesuperconductorordinary metalnot zeronear 0 Kexactly zeroBelow its critical temperature asuperconductor’s resistivity is exactlyzero. Sketch, not to scale.
  • Cool some materials below their critical temperature (transition temperature), Tc.
  • Resistivity drops suddenly to exactly zero: a superconductor.
  • Tc depends on the material.
  • Zero resistance: no heating. A current in a superconducting loop keeps flowing.
Mission 6

Using superconductors

  • Very large currents with no heating → very strong magnetic fields.
  • MRI scanners and particle accelerators use superconducting electromagnets.
  • The cost: cooling. Liquid helium (4 K) is expensive; liquid nitrogen (77 K) is cheap.
Quick check
?A cable is made from a ceramic superconductor with a critical temperature of 92 K. Which statement is correct?
Mission check

?An unlabelled wire has a mean diameter of 0.32 mm. Its resistance between the clips is 1.72 Ω at a length of 0.20 m and 5.37 Ω at 0.80 m. Resistivities: copper 1.7 × 10⁻⁸ Ω m; iron 1.0 × 10⁻⁷ Ω m; constantan 4.9 × 10⁻⁷ Ω m; nichrome 1.1 × 10⁻⁶ Ω m. Which metal is the wire most likely made of?
Recap

The big ideas

Mission 1

  • Current = rate of flow of charge; 1 A = 1 C s⁻¹.
  • I = Q/t.
  • Conventional current: the way positive charge would move; electrons in metals move the other way.
  • Charge is conserved: the current into a component equals the current out.

Mission 2

  • Potential difference = energy transferred per unit charge; 1 V = 1 J C⁻¹.
  • V = W/q.
  • emf: energy given to the charge per unit charge, in the source; pd: energy given up per unit charge, in components.

Mission 3

  • R = V/I, in ohms (1 Ω = 1 V A⁻¹). Ohm's law: I ∝ V at constant temperature.
  • Resistance comes from collisions of free electrons with vibrating lattice ions, which also heat the conductor.
  • I–V practical: ammeter in series, voltmeter in parallel, small currents to keep a wire at constant temperature.
  • Filament lamp: R rises as it heats; find R from V/I, not from a tangent.
  • NTC thermistor and LDR: R falls with more heat or light (more charge carriers).

Mission 4

  • Diode: current in one direction only, after a threshold of about 0.6 V (silicon).
  • Warming: metal R rises (more collisions); NTC thermistor R falls (many more carriers).
  • NTC R–T practical: water bath, multimeter or small-current ammeter–voltmeter, plot R against θ.

Mission 5

  • R = ρl/A: resistivity is set by the material and temperature; length and area set the resistance.
  • Hotter metal: ions vibrate more, more collisions, more resistance.

Mission 6

  • Measure ρ: mean diameter by micrometer, R against length, ρ = gradient × A.
  • Below its critical temperature a superconductor has zero resistivity: no heating, very strong magnetic fields.
🏆

Mini-lesson complete!

⭐⭐⭐

You've worked through Forces, Energy and Electricity (part 4) for CCEA A-level Physics. 🎉

  1. Mission 1A lamp glows while charge flows through it. Does any of the charge get used up on the way?
  2. Mission 2A battery is marked one and a half volts, a lamp six. What exactly does a volt count?
  3. Mission 3Double the potential difference across a wire. When does the current exactly double?
  4. Mission 4Heat a metal wire and its resistance rises. Heat a thermistor and it falls. Why the difference?
  5. Mission 5Stretch a metal wire to twice its length. What happens to its resistance?
  6. Mission 6A ruler, a micrometer, an ammeter and a voltmeter. How can they tell you what a wire is made of?

Your stars: 0 / 0

📣 Smashed it? Share your score

Challenge a friend to beat your stars, or show a parent how you got on.

→ Back to A-Level Physics · CCEA