← A-Level Physics · AQA · A-Level Physics revision
⭐ 0
AQA A-level Physics (7408) · 3.3 Waves (part 3)
Mini-Lesson

Waves (part 3)

6 missions. Guess, learn, then check. Your place is saved.

  1. Mission 1Two slits, a laser and a ruler: how can stripes on a wall measure a wavelength far thinner than a hair?
  2. Mission 2How do you measure the wavelength of light with two slits, and why did it take so long to be believed?
  3. Mission 3You can hear someone around a corner but not see them. What decides how much a wave spreads?
  4. Mission 4How can a slide ruled with thousands of fine lines measure the wavelength of light?
  5. Mission 5Why does light bend as it enters water, but not when it hits the surface head-on?
  6. Mission 6How can light stay trapped inside a thin glass strand, even when the strand bends?
Mission 1

Mission 1: Two slits, a laser and a ruler: how can stripes on a wall measure a wavelength far thinner than a hair?

Make a guess: Two slits, a laser and a ruler: how can stripes on a wall measure a wavelength far thinner than a hair?

Quick check
?Predict first. Monochromatic light passes through two very narrow slits and falls on a distant screen, producing a pattern of bright and dark bands. Which explanation accounts for this pattern?
Mission 1

Young's double slit

Young's double-slit set-uplaserdouble slitscreenPTwo paths to P, a bright fringe: pathdifference λ (here n = 1).Bright fringe: path difference nλ. Dark: (n+ ½)λ. Middle fringe: bright (pathdifference 0).Not to scale: the screen is much moredistant than the slit separation (break inthe axis).
  • Monochromatic light (e.g. a laser) → two narrow slits, very close together → a screen far away.
  • Light diffracts (spreads out) from each slit. The two spreading waves overlap and interfere.
  • Both slits are lit by the same wavefronts, so they act as coherent sources.
  • Bright fringe: path difference nλ. Dark fringe: path difference (n + ½)λ.
  • Result: equally spaced bright and dark fringes, with a bright fringe in the centre.
Mission 1

The fringe-spacing equation

Double-slit geometrys = slitseparationD = slits-to-screen distancew = fringe spacingNot to scale: D ≫ s.
  • Fringe spacing = λ × (slits-to-screen distance) ÷ (slit separation).
  • w = λD/s: w = fringe spacing, s = slit separation, D = slits-to-screen distance.
  • Valid when the screen is far away compared with the slit separation (small angles).
Mission 1

Worked example

  • Laser light of wavelength 633 nm. Slits 0.50 mm apart. Screen 2.00 m from the slits.
  • w = λD/s = (633 × 10⁻⁹ × 2.00)/(0.50 × 10⁻³) = 2.5 × 10⁻³ m
  • Fringes 2.5 mm apart: easy to measure. A wavelength of 0.000 000 633 m becomes millimetres on the screen.
  • Turn it around: measure the fringe spacing, slit separation and distance, and calculate λ.
Quick check
?In a Young's double-slit experiment, monochromatic red light is incident normally on the slits and the fringe separation on the screen is 2.0 mm. Which single change would make the fringe separation 4.0 mm?
Mission check

?Laser light passes through two slits 0.25 mm apart onto a wall 2.50 m away. A student measures across six fringe spacings: the fringes span 39.0 mm. What is the wavelength of the light?
Mission 2

Mission 2: How do you measure the wavelength of light with two slits, and why did it take so long to be believed?

Make a guess: How do you measure the wavelength of light with two slits, and why did it take so long to be believed?

Mission 2

Setting up

Young's slits bench set-upSeen from above (not to scale)laserdouble slitslit separation0.1–0.5 mmscreentape measure: slits-to-screen distance,1–3 mThe fringes on the screen, face-on1st11th10 spacingsFringe spacing = distance ÷ 10. Countspacings, not fringes.No laser? Lamp, filter, single slitlampfiltersingleslitdoubleslitto screenThe single slit lights both slits from onepoint, so they are coherent.
  • Laser → double slit (slit separation about 0.1–0.5 mm) → screen 1–3 m away. Darkened room.
  • The laser is monochromatic and coherent: one wavelength, with both slits lit by the same wavefronts.
  • No laser? A filament lamp, a colour filter, then a single slit before the double slit. The single slit lights both slits from one point, so they are coherent.
  • Follow the laser safety rules.
Mission 2

Measuring well

  • Slit separation: from the manufacturer, or measured with a travelling microscope.
  • Slits-to-screen distance: metre rule or tape. Large, so its percentage uncertainty is small.
  • Fringe spacing: measure across many fringes (say 10 spacings) and divide. One spacing of about 2 mm would carry a huge percentage uncertainty.
  • Count spacings, not fringes: from the 1st to the 11th bright fringe is 10 spacings.
  • Better: repeat at several screen distances. Plot fringe spacing against distance: a straight line through the origin, gradient = λ ÷ slit separation.
Mission 2

Worked example

Measuring across ten fringe spacingsIllustrative drawing of the fringes1st11th23456789100510152023.5mm23.5 mm = 10 spacingsFringe spacing = 23.5 mm ÷ 10 = 2.35 mmEqually spaced bright fringes; drawn to theruler’s scale. Illustrative, not aphotograph.
  • Slit separation 0.50 mm. Screen 1.85 m away. From the 1st to the 11th bright fringe: 23.5 mm.
  • Fringe spacing = 23.5 ÷ 10 = 2.35 mm.
  • λ = ws/D = (2.35 × 10⁻³ × 0.50 × 10⁻³)/1.85
  • λ = 6.35 × 10⁻⁷ m ≈ 6.4 × 10⁻⁷ m (640 nm, red).
  • Ruler reading ±0.5 mm: 2% of 23.5 mm, but 21% of a single 2.35 mm spacing.
Quick check
?A student doubles the slits-to-screen distance and, at the same time, swaps the double slit for one with twice the slit separation. The laser is unchanged. What happens to the fringe spacing?
Mission 2

White-light fringes

White-light fringesWhite light through a double slitcentral fringe: white1st2nd1st2ndWhere each colour is bright (same scale):violetredviolet spacingred: about 7/4 of itFringe spacing ∝ wavelength: violet nearestthe centre, red furthest out. Further out,orders overlap and the colours blur intowhitish light.Colours computed by adding equally spacedfringes for every wavelength from 400 nm to 700nm (approximate colour rendering).
  • Central fringe: white. Path difference zero, so every wavelength is bright there.
  • Either side: coloured fringes, each a small spectrum.
  • Fringe spacing ∝ λ, so violet/blue is nearest the centre and red is furthest out.
  • Further out, the colours from different orders overlap. After a few fringes the pattern fades into an even, whitish light.
Quick check
?In a white-light pattern, the red edge (700 nm) of the first bright fringe is 3.5 mm from the centre of the central white fringe. How far from that centre is the violet edge (400 nm) of the same fringe?
Mission 2

Particles or waves?

Particles or waves: a timelineNewton: particles“Corpuscles”. Predicts lightis faster in water.late 1600sHuygens: wavesPredicts light is slower inwater.late 1600sNewton’s theory preferred forabout a centuryHis reputation; sharp shadows;waves could not explainpolarisation.Young: two-slit fringesAbout 1801–1803. Dark fringes:light + light can givedarkness.1801–1803Fresnel: wave theoryMathematical theory of wavesand diffraction.1810sLight is slower in waterAs the wave theory predicted.1850Maxwell: EM wavesLight is an electromagneticwave.1860sPhotonsPhotoelectric effect bringsback particles.1900sDates approximate. Orange: particle theory;blue: wave theory; purple: photons.
  • Newton (late 1600s): light is a stream of particles ("corpuscles"). Explained reflection and refraction; predicted light travels faster in water.
  • Huygens (same period): light is a wave. Predicted light travels slower in water.
  • Newton's theory was preferred for about a century: his huge reputation; sharp shadows (light's tiny λ makes diffraction hard to see); and Huygens' waves could not explain polarisation.
  • Young (about 1801–1803): two-slit fringes. Dark fringes, where light from both slits arrives, mean light + light can give darkness. Waves can cancel; particles cannot.
  • Acceptance was slow. Fresnel's mathematical wave theory (1810s) and the measurement (1850) that light is slower in water settled it.
  • Later: Maxwell showed light is an EM wave (1860s); the photoelectric effect (1900s) brought back particles: photons. Understanding changes with evidence.
Quick check
?In 1818, Fresnel's wave theory predicted a surprise: a small bright spot at the very centre of the shadow of a round disc. Arago looked and found it. Why did this count against a particle theory?
Mission check

?A student measures from the centre of the 1st bright fringe to the centre of the 9th bright fringe with a ruler: 42.0 mm, with an uncertainty of ±0.5 mm. What is the fringe spacing, and what percentage uncertainty does this reading carry into the wavelength?
Mission 3

Mission 3: You can hear someone around a corner but not see them. What decides how much a wave spreads?

Make a guess: You can hear someone around a corner but not see them. What decides how much a wave spreads?

Quick check
?Predict first. A wavefront diagram shows straight water waves of wavelength 2.0 cm, with wavefronts parallel to a barrier, passing through a gap 6.0 cm wide in the barrier; beyond the gap the wavefronts are straight in the middle and curved only at the edges. The gap is narrowed to 0.40 cm. How do the wavefronts beyond the gap change?
Mission 3

Diffraction

Diffraction at gaps and obstaclesGap ≈ λ: strong spreadingλλGap ≈ 5λ: little spreadingSmall obstacle: waves close up behind itAt a doorway (seen from above)Sound: λ ≈ 0.3–3 mbends around the edgessharp shadowsharp shadowLight: λ ≈ 4–7 × 10⁻⁷ mgoes almost straight
  • Diffraction: a wave spreads out as it passes through a gap or around the edge of an obstacle.
  • Speed, frequency and wavelength are unchanged. Only the direction of travel spreads.
  • Spreading becomes significant when the gap is comparable with λ. The narrower the gap, the more it spreads.
  • Gap about λ or smaller: nearly semicircular wavefronts, spreading through almost 180°.
  • Gap much wider than λ: very little spreading; a sharp-edged "shadow".
  • Speech: λ ≈ 0.3–3 m, like doorways. Light: λ ≈ 4–7 × 10⁻⁷ m, far smaller than any doorway.
Mission 3

Huygens and wavefront diagrams

Secondary wavelets at a gapλλwavefrontrayshadowshadownew wavefrontray at 90°to wavefrontEach point on the wavefront is a source ofsecondary wavelets.Wavelet after one period: radius λ.New wavefront: the line touching all thewavelets.
  • Huygens' construction: every point on a wavefront acts as a source of secondary wavelets. The new wavefront is the line touching all the wavelets.
  • At a gap, only part of the wavefront gets through. Wavelets from its edges spread into the "shadow".
  • Wavefront diagram: rays at 90° to wavefronts. Wavefront spacing (λ) stays the same beyond the gap.
  • Wide gap: straight in the middle, curved at the edges. Narrow gap: nearly semicircular.
Quick check
?Predict first. Monochromatic light of wavelength 600 nm is incident normally on a single slit, and the diffraction pattern is viewed on a distant screen. The slit width is then reduced from 0.20 mm to 0.10 mm. How does the central maximum change?
Mission 3

Light through one slit

Single-slit diffraction patternlasersingle slitscreenPattern on the screenintensityposition on screen4.7%1.6%side peaks, as % ofthe central peaksidecentral maximumtwice as wide as each side maximumNarrower slitwider, dimmer central maximum (dashed: firstslit)intensityposition on screenWhite light (schematic)violetredWhite centre with coloured edges; sidemaxima are spectra, violet nearest thecentre, red furthest out.Graphs to scale; bands drawn brighter thantrue so the faint ones show.
  • Laser light through one narrow slit gives bright and dark bands, not a slit-shaped patch.
  • Central maximum: brightest, and twice as wide as each side maximum.
  • Side maxima: much dimmer, fainter the more distant they are from the centre.
  • Narrower slit → wider central maximum (and dimmer: less light gets through).
  • Longer λ (red rather than blue) → wider central maximum.
  • White light: a white central maximum with coloured edges; side maxima are spectra, violet nearest the centre, red furthest out.
Mission check

?Sea waves reach a harbour wall with a 20 m wide entrance. A boat is moored behind the wall, well to one side of the entrance. On day 1 the waves have a wavelength of 20 m; on day 2, 2.0 m, with the same amplitude. On which day is the boat rocked more, and why?
Mission 4

Mission 4: How can a slide ruled with thousands of fine lines measure the wavelength of light?

Make a guess: How can a slide ruled with thousands of fine lines measure the wavelength of light?

Mission 4

What a grating is

Diffraction grating and beamslasergratingscreenn = −2n = −1n = 0n = +1n = +2zoom:dSpots are not equally spaced: sin θ, not θ,is proportional to the order.
  • A diffraction grating: a plate with many equally spaced, parallel slits (lines).
  • Slit spacing d = 1 ÷ (lines per metre). 300 lines per mm → d = 1/300 mm = 3.33 × 10⁻⁶ m.
  • Each slit diffracts, so light from all the slits overlaps and interferes.
  • Bright beams leave only at certain angles: where light from every slit arrives in phase.
Mission 4

Deriving the grating equation

Deriving the grating equationnormal incidencenormalθθdextra path = d sin θ(path difference)parallel rays to a distant screenRight-angled triangle: hypotenuse d (betweenadjacent slits), side d sin θ opposite θ.
  • Light hits the grating at normal incidence (straight on).
  • Look at light leaving two adjacent slits at angle θ. Extra path for the lower slit: d sin θ.
  • In phase when this path difference is a whole number of wavelengths:
  • d sin θ = nλ, n = 0, 1, 2, … (the order).
  • If adjacent slits are in phase, all the slits are in phase.
  • n = 0: the zero order, straight through (θ = 0).
  • Highest order: sin θ cannot exceed 1, so n ≤ d/λ.
Mission 4

Worked example

  • 300 lines per mm, red laser λ = 633 nm.
  • d = 1 ÷ (300 × 10³) = 3.33 × 10⁻⁶ m.
  • First order: sin θ = λ/d = 633 × 10⁻⁹ ÷ 3.33 × 10⁻⁶ = 0.190 → θ = 10.9°.
  • Second order: sin θ = 2λ/d = 0.380 → θ = 22.3°.
  • Highest order: d/λ = 5.27 → n = 5 (at 71.7°). Total beams: 5 + 5 + 1 = 11.
  • No small-angle shortcut: angles are large. Use sin θ.
Quick check
?Light of wavelength 650 nm is incident normally on a diffraction grating that has 600 lines per millimetre. At what angle to the straight-through direction is the second-order maximum observed?
Quick check
?Predict first. Monochromatic light is incident normally first on a double slit and then on a diffraction grating whose adjacent slits have the same separation d as the double slit. Every slit is equally illuminated. Compared with the double-slit fringes, how do the grating's principal maxima appear?
Mission 4

Why use many slits?

Two slits compared with a gratingTwo slits, spacing dbroad fringesintensityλ/d2λ/dsin θGrating: 5 slits, same spacing dsame angles; much sharper and brighterintensityλ/d2λ/dsin θSame scales in both graphs. A real gratinghas thousands of slits: its maxima aresharper still.
  • Same d, same λ: grating maxima are at the same angles as double-slit fringes.
  • But with many slits, a tiny step away from those angles puts the slits out of step and they cancel.
  • So the maxima are very sharp and very bright, with darkness between. Angles can be measured precisely.
  • Smaller d (more lines per mm) → orders farther apart.
Quick check
?Predict first. White light is incident normally on a diffraction grating. Which describes the pattern seen on a screen?
Mission 4

White light and spectra

White-light spectra from a gratingzero order: white1st2nd3rdoverlapEach order: violet nearest the middle, redfarthest (sin θ ∝ λ).Overlap: 2nd-order red (2 × 700 = 1400 nm)lies beyond 3rd-order violet (3 × 400 = 1200nm).Hydrogen lamp, first order: a line spectrum656486434410wavelength (nm)Strip: position proportional to sin θ.
  • Zero order is white: every wavelength has θ = 0 there.
  • Each other order is a spectrum: violet (short λ) nearest the centre, red farthest, since sin θ ∝ λ.
  • Higher orders spread wider and can overlap: second-order red (2 × 700 = 1400 nm) lies beyond third-order violet (3 × 400 = 1200 nm).
  • A gas-discharge lamp gives a line spectrum: separate bright coloured lines in each order, one per wavelength.
  • Uses: measuring wavelengths, identifying elements from their spectral lines (in labs and in starlight), spectrometers.
Mission 4

Measuring λ with a laser

Measuring wavelength with a laser and gratinglasergratingscreen2xxn = 2n = 2θD: grating to screen(metre rule)!Never look into the beamor its reflections.tan θ = x/D → θ → λ = d sin θ / nTop view, not to scale.
  • Laser beam normal to the grating; screen a measured distance D away (≈ 1 m).
  • Measure the distance 2x between the two nth-order spots, either side of the centre. Halve it: x.
  • tan θ = x/D → θ → λ = d sin θ / n.
  • Use the highest order you can measure, and a large D: smaller percentage uncertainty.
  • Repeat for several orders and average (or plot sin θ against n: gradient λ/d).
  • Safety: never look into the beam or its reflections; keep reflective surfaces out of the beam path.
Mission check

?A laser beam is directed normally at a grating with 500 lines per mm. On a screen 1.00 m from the grating, the two second-order spots are 1.50 m apart. What is the wavelength of the laser light?
Mission 5

Mission 5: Why does light bend as it enters water, but not when it hits the surface head-on?

Make a guess: Why does light bend as it enters water, but not when it hits the surface head-on?

Quick check
?Circular ripples spread out across a ripple tank from a vibrating dipper. A student sketches a wavefront–ray diagram of the waves. Which statement correctly describes the rays on the diagram?
Mission 5

Wavefronts and rays

Wavefronts and raysPoint sourceDistant sourceλλwavefrontrayWavefronts drawn one wavelength apart (everycrest).
  • Wavefront: a line (or surface) joining points that are in phase, e.g. every crest.
  • Neighbouring wavefronts are one wavelength apart.
  • Ray: a line perpendicular to the wavefronts, showing the direction the wave's energy travels.
  • Point source: circular wavefronts, rays spreading out.
  • Distant source or laser: straight (plane) wavefronts, parallel rays.
Mission 5

Reflection

Law of reflectionmirrornormalangle ofincidenceangle ofreflection40°40°Both angles are measured from the normal, notfrom the mirror.
  • The normal: a line at 90° to the surface where the ray hits it.
  • Measure every angle from the normal, not from the surface.
  • Law of reflection: angle of incidence = angle of reflection.
  • Incident ray, reflected ray and normal lie in the same plane.
  • Reflection changes direction only: speed, frequency and wavelength stay the same.
Mission 5

Why refraction happens

Refraction of wavefrontsairweak reflectionnormalglassbends towards the normalHead on: slower, shorter wavelength, nochange of directionλ in airλ in glassSpacing in glass : air = 2 : 3 (n = 1.5);frequency unchanged.Drawn to scale for n = 1.5 at 50° incidence(refracted angle 30.7°).
  • At a boundary, part of a wave is reflected and part is transmitted.
  • The transmitted wave changes speed. Its frequency stays the same (set by the source), so its wavelength changes too: wavelength = speed ÷ frequency.
  • Hitting at an angle, one end of each wavefront reaches the boundary first and slows first. The wavefront turns, so the ray changes direction: refraction.
  • Into a slower medium: wavefronts closer together, ray bends towards the normal.
  • Into a faster medium: ray bends away from the normal.
  • Along the normal: the whole wavefront slows at once. Speed and wavelength change; the direction does not.
  • Water waves travel more slowly in shallower water. In a ripple tank, a shallow region refracts waves as glass refracts light.
Mission 5

Refractive index

  • n = c/cs: speed of light in a vacuum ÷ speed in the substance, cs.
  • No unit. Vacuum: n = 1 exactly. Air: n ≈ 1.00 (1.0003).
  • Water 1.33 · typical glass about 1.5 · diamond 2.42.
  • Larger n, slower light.
Quick check
?The refractive index of a certain plastic is 1.5. Which statement correctly describes what this value means?
Mission 5

Snell's law

  • n1 sin θ1 = n2 sin θ2, with both angles measured from the normal.
  • Into larger n: smaller angle (towards the normal). Into smaller n: larger angle (away).
  • θ1 = 0 gives θ2 = 0: no bending along the normal.
Mission 5

Worked example

  • Light of wavelength 589 nm in air enters water (n = 1.33) at 60.0° to the normal.
  • 1.00 × sin 60.0° = 1.33 × sin θ2 → sin θ2 = 0.651 → θ2 = 40.6°.
  • Speed in water = c/n = 3.00 × 10⁸ ÷ 1.33 = 2.26 × 10⁸ m s⁻¹.
  • Same frequency, so the wavelength falls by the same factor: 589 ÷ 1.33 = 443 nm.
  • Check: 40.6° < 60.0°, so the ray bent towards the normal, as it should entering a slower medium.
Quick check
?A ray of light passes from air into a transparent liquid. The incident ray makes an angle of 40.0° with the surface of the liquid and the refracted ray makes an angle of 55.0° with the surface. The speed of light in air is 3.00 × 10⁸ m s⁻¹. What is the speed of light in the liquid?
Mission check

Wavefront–ray diagram. A horizontal line labelled boundary separates region X (above) from region Y (below). In X the wanormalXYboundaryray
?The diagram shows straight water waves in a ripple tank crossing the boundary between region X and region Y. The wavefronts, a ray and the normal at the point where the ray crosses the boundary are drawn. Which statement is correct?
Mission 6

Mission 6: How can light stay trapped inside a thin glass strand, even when the strand bends?

Make a guess: How can light stay trapped inside a thin glass strand, even when the strand bends?

Mission 6

Heading into a lower n

Towards the critical angleLess than the critical angleairglassrefractedweak reflectionAt the critical angleairglassrefracted ray alongthe boundary (90°)strongreflectioncritical angleMore than the critical angleairglassall reflectedno light leavesDrawn for glass (n = 1.50) to air. Ray widthsshow roughly how much light goes each way.
  • Light going from glass into air (larger n to smaller n) bends away from the normal.
  • Increase the angle of incidence: the refracted ray swings towards the surface.
  • At the critical angle, the refracted ray runs along the boundary (angle of refraction 90°).
  • Beyond the critical angle no light leaves: all of it reflects back. This is total internal reflection (TIR).
  • Below the critical angle there is also a partial reflection, growing stronger as the angle nears the critical angle.
  • TIR obeys the law of reflection.
Mission 6

The critical angle

  • Put θ2 = 90° (sin 90° = 1) into Snell's law.
  • sin θc = n2/n1, light going from n1 into n2 (n1 > n2).
  • Glass (1.50) to air: 41.8°. Water (1.33) to air: 48.8°.
  • TIR needs both: light heading into a medium of lower n, and angle of incidence greater than the critical angle.
Quick check
?Light can cross a flat boundary between water (n = 1.33) and glass (n = 1.50) in either direction. Which statement about total internal reflection at this boundary is correct?
Mission 6

Worked example: will it reflect?

  • A ray in water (n = 1.33) meets the water surface. Critical angle: sin⁻¹(1/1.33) = 48.8°.
  • At 50.0° to the normal: 50.0° > 48.8°, so TIR. No light leaves.
  • At 45.0°: 45.0° < 48.8°, so it refracts out. 1.33 × sin 45.0° = 1.00 × sin θ2 → sin θ2 = 0.940 → θ2 = 70.1°.
  • Always compare the angle from the normal with the critical angle.
Quick check
?A glass block of refractive index 1.52 is under water of refractive index 1.33. A ray inside the glass meets the glass–water boundary at an angle of incidence of 55.0°. What happens to the ray?
Mission 6

Step-index optical fibre

Step-index optical fibreLong sectioncore (higher n)cladding (lower n)Total internal reflection at the core–cladding boundary: angle of incidencegreater than the critical angle.Cross-sectionn across the fibren₁n₂n₁ > n₂n₁n₂corestepWidths and the index step exaggerated; not toscale.
  • A thin glass core (higher n) inside a glass cladding (slightly lower n).
  • Light meets the core–cladding boundary at more than the critical angle, so it is totally internally reflected, again and again, along the core.
  • Step index: n drops suddenly at the core–cladding boundary.
  • Cladding: keeps TIR at a boundary that cannot be scratched or dirtied, and stops light crossing between fibres that touch (signal security).
  • The fibre can bend gently. A sharp bend makes the angle of incidence fall below the critical angle, and light leaks out.
Quick check
?An optical fibre has a core of refractive index 1.52 and a cladding of refractive index 1.46. What is the critical angle at the core–cladding boundary?
Mission 6

Pulse broadening: many paths

Pulse broadeningOne pulsepulse inpulse out: broadenedThe zig-zag path (orange) is longer than theaxial path (blue): its light arrives later.Two pulsessent apartarrive overlappingBroadened pulses overlap and merge.Absorptionnear the startfurther alongEnergy absorbed: amplitude falls, and thearea under the pulse falls.Illustrative shapes; power against time, noscale. Without absorption the area under apulse stays the same.
  • Data travel as short pulses of light.
  • In a wide core, light takes different paths: straight along the axis, or zig-zagging at steeper angles. Longer paths take longer.
  • So a short pulse arrives spread out in time: pulse broadening.
  • This is modal dispersion.
  • Broadened pulses overlap and merge. This limits the data rate and the distance a signal can travel.
  • Fix: a very narrow core (a few μm instead of about 50 μm) allows only one path. This is a monomode fibre: much higher data rates over much longer distances.
Mission 6

Material dispersion and absorption

Pulse broadeningOne pulsepulse inpulse out: broadenedThe zig-zag path (orange) is longer than theaxial path (blue): its light arrives later.Two pulsessent apartarrive overlappingBroadened pulses overlap and merge.Absorptionnear the startfurther alongEnergy absorbed: amplitude falls, and thearea under the pulse falls.Illustrative shapes; power against time, noscale. Without absorption the area under apulse stays the same.
  • The refractive index of glass depends slightly on wavelength: shorter wavelengths travel a little more slowly.
  • A source giving a range of wavelengths sends them at different speeds: material dispersion, another cause of pulse broadening.
  • Fix: a monochromatic source (a laser).
  • Absorption: the glass absorbs some energy, so the pulse's amplitude falls along the fibre.
  • Fix: very pure glass, and regenerators (or amplifiers) at intervals along the cable.
Quick check
?Two multimode fibres of the same length have identical cores. Fibre P's cladding has a refractive index closer to the core's than fibre Q's, so P has the larger critical angle at the core–cladding boundary. Which fibre broadens pulses less, and why?
Mission check

?An optical fibre has a glass core of refractive index 1.50, surrounded by glass of refractive index 1.40. On a straight stretch, a ray meets the core's wall at 75° to the normal. Where the fibre bends, the same ray meets the wall at 66° to the normal. What happens at each point?
Recap

The big ideas

Mission 1

  • Two coherent slits → equally spaced bright and dark fringes; bright where path difference = nλ.
  • w = λD/s.

Mission 2

  • Measure fringe spacing across many fringes; count spacings, not fringes. Large screen distance, small percentage uncertainty.
  • White light: white central fringe, coloured fringes with violet nearest the centre.
  • Young's dark fringes were classical evidence for waves; Newton's particle theory held on for a century, until more evidence (Fresnel, light slower in water) settled it.

Mission 3

  • Diffraction is significant when the gap or obstacle is comparable with λ, and greater the narrower the gap; λ itself does not change.
  • Single slit: wide, bright central maximum; narrower slit or longer λ → wider pattern.

Mission 4

  • Grating at normal incidence: d sin θ = nλ, d = 1/(lines per metre); n ≤ d/λ.
  • Many slits → same angles as a double slit, but much sharper, brighter maxima.

Mission 5

  • Rays are perpendicular to wavefronts. Reflection: angle of incidence = angle of reflection, measured from the normal.
  • n = c/cs. Refraction is caused by a change of speed; frequency is unchanged, wavelength changes.
  • n1 sin θ1 = n2 sin θ2: towards the normal into larger n.

Mission 6

  • TIR: light heading into lower n at more than the critical angle is all reflected.
  • sin θc = n2/n1.
  • Step-index fibre: TIR at the core–cladding boundary; the cladding protects the core and stops cross-talk.
  • Different path lengths broaden pulses (modal / multimode dispersion); a monomode fibre fixes it.
🏆

Mini-lesson complete!

⭐⭐⭐

You've worked through Waves (part 3) for AQA A-level Physics. 🎉

  1. Mission 1Two slits, a laser and a ruler: how can stripes on a wall measure a wavelength far thinner than a hair?
  2. Mission 2How do you measure the wavelength of light with two slits, and why did it take so long to be believed?
  3. Mission 3You can hear someone around a corner but not see them. What decides how much a wave spreads?
  4. Mission 4How can a slide ruled with thousands of fine lines measure the wavelength of light?
  5. Mission 5Why does light bend as it enters water, but not when it hits the surface head-on?
  6. Mission 6How can light stay trapped inside a thin glass strand, even when the strand bends?

Your stars: 0 / 0

📣 Smashed it? Share your score

Challenge a friend to beat your stars, or show a parent how you got on.

→ Back to A-Level Physics · AQA