← A-Level Physics · AQA · A-Level Physics revision
⭐ 0
AQA A-level Physics (7408) · 3.6.1 SHM energy, pendulums and resonance
Mini-Lesson

SHM energy, pendulums and resonance

4 missions. Guess, learn, then check. Your place is saved.

  1. Mission 1Take a pendulum clock to the Moon. Does it run fast, run slow, or keep time?
  2. Mission 2A mass on a spring keeps stopping and starting again. Where is its energy at the instant it stops?
  3. Mission 3Why can small pushes, timed just right, build up a huge swing?
  4. Mission 4Engineers add damping to bridges, cars and doors. How much damping is just right?
Mission 1

Mission 1: Take a pendulum clock to the Moon. Does it run fast, run slow, or keep time?

Make a guess: Take a pendulum clock to the Moon. Does it run fast, run slow, or keep time?

Mission 1

Mass on a spring

Mass on a spring, horizontal and verticalHorizontalmkequilibriumspring unstretchedVerticalkmend of unstretched springequilibrium: lowerextension = mg/kSame period in bothg only shifts the equilibrium position
  • T = 2π√(m/k)
  • m = oscillating mass; k = spring constant.
  • Bigger mass → longer T. Stiffer spring → shorter T.
  • Not on g: hung vertically, gravity only shifts the equilibrium position. Same T as horizontal.
  • Not on amplitude.
Mission 1

Simple pendulum

Simple pendulumθequilibriumlpivot to centreof bobmgmg sin θrestoring forceSmall angle θ (here 10°)
  • T = 2π√(l/g)
  • Length from the pivot to the centre of mass of the bob.
  • Small angles only. Then the restoring force is (nearly) proportional to the displacement.
  • This uses the small-angle approximation: sin θ ≈ θ (θ in radians).
  • Not on the bob's mass. Not on the (small) amplitude.
  • Other oscillators (e.g. liquid in a U-tube) can appear: the question gives the period equation; use it as given.
Mission 1

Worked examples

  • Spring: m = 0.25 kg, k = 40 N m⁻¹. T = 2π√(0.25/40) = 0.50 s.
  • Pendulum, length 0.80 m:
  • T = 2π√(0.80/9.81) = 1.8 s (g = 9.81 m s⁻²).
  • To make the pendulum's period three times as long: nine times the length.
Quick check
?A trolley hung from a newton meter gives a reading of 14.7 N. The trolley is then attached to a spring system on a horizontal track and oscillates with negligible friction. The spring constant of the system is 7.50 N m⁻¹. Take g = 9.81 m s⁻². What is the time period of the oscillation?
Mission 1

What sets the period?

What sets the periodChangePeriodMass on a springMore masslongerStiffer springshorterLarger gsameLarger amplitudesamePendulumLonger stringlongerLarger gshorterHeavier bobsameLarger (small) amplitudesame
  • Mass on a spring: longer with more mass; shorter with a stiffer spring. Unchanged by g and by amplitude.
  • Pendulum: longer with a longer string; shorter where g is larger. Unchanged by the bob's mass and by small changes of amplitude.
  • Large swings (beyond about 10°): a pendulum's period grows slightly. The motion is no longer quite SHM.
Mission 1

Measuring the period

Measuring the period of a pendulumclamplstopwatch: time20 oscillationsfiducial marker atequilibriumT² / s²l / m0gradient= 4π²/gg = 4π² ÷ gradient
  • Time many oscillations (e.g. 20) and divide. Repeat and average.
  • Start and stop as the mass passes equilibrium, at a fiducial marker: it moves fastest there, so the instant is sharp.
  • Pendulum: keep angles small; measure l to the centre of the bob.
  • Pendulum: plot T² against l. Straight line through the origin, gradient 4π²/g → g = 4π² ÷ gradient.
  • Spring: plot T² against m. Gradient 4π²/k → k = 4π² ÷ gradient.
Quick check
?A long simple pendulum hangs in the stairwell of a school. Swinging with a small amplitude, its bob takes 2.10 s to move from one extreme position to the other. Take g = 9.81 m s⁻². What is the length of the pendulum?
Mission check

?A simple pendulum and a mass–spring oscillator each have a period of 1.0 s on Earth. Both are taken to a planet where the gravitational field strength is four times as large as on Earth, and both oscillate with small amplitude. What are their new periods?
Mission 2

Mission 2: A mass on a spring keeps stopping and starting again. Where is its energy at the instant it stops?

Make a guess: A mass on a spring keeps stopping and starting again. Where is its energy at the instant it stops?

Quick check
?A mass on a horizontal spring moves with simple harmonic motion on a frictionless surface; air resistance is negligible. Which statement about the energy of the oscillator is correct?
Mission 2

Energy swaps back and forth

Energy at the turning points and at equilibriumkineticpotentialtotalAt −A: at rest0At equilibrium: fastest0At +A: at rest0−A0+ATotal the same inevery row
  • Total energy = Ek + Ep
  • At ±A (turning points): at rest. Kinetic energy zero; potential energy maximum = the total.
  • At equilibrium: fastest. Kinetic energy maximum; potential energy minimum.
  • Potential energy: in the spring (mass–spring) or gravitational (pendulum).
  • Undamped: the total stays constant. Energy is only exchanged.
Mission 2

Energy against displacement

Energy against displacementenergyx−A+A0totalkineticpotentialAt every x: kinetic + potential = total
  • Potential energy: a U-shaped parabola, zero at x = 0, maximum at ±A.
  • Kinetic energy: an upside-down parabola, maximum at x = 0, zero at ±A.
  • Total: a horizontal line. At every x, kinetic + potential = total.
  • Mass–spring: elastic potential energy E = ½kx²
Mission 2

Energy against time

Energy against timeDisplacement x+A−AEnergy0T/2TtttotalkineticpotentialTwo peaks each per period; never negative;sum constant.
  • Kinetic and potential energy each rise and fall twice per period: two peaks per cycle.
  • Both are never negative: each is 0 at its minimum.
  • When one is at a peak, the other is zero. Their sum is constant.
  • (x = A cos ωt gives PE ∝ cos²ωt and KE ∝ sin²ωt.)
Quick check
Graph of Eₚ (J) on the vertical axis against x (m) on the horizontal axis. The vertical axis is marked 0 at the horizont0.400−0.10−0.0500.050.10Eₚ / Jx / mtotal energy
?A block attached to an ideal spring oscillates on a horizontal surface with negligible friction. The graph shows the elastic potential energy Ep of the block–spring system as a function of the block's position x, measured from equilibrium; the curve is a parabola, and the dashed line shows the system's total energy. What is the kinetic energy of the block when it is at x = 0.050 m?
Mission 2

Total energy and amplitude

  • At x = ±A all the energy is potential.
  • Mass–spring: Etotal = ½kA².
  • E ∝ A²: double the amplitude → four times the energy, twice the maximum speed.
  • Halfway out (x = A/2): PE = ¼ of the total. KE = ¾, not ½.
Mission 2

Speed from energy

  • Energy at any x: ½mv² = ½k(A² − x²). With k = mω²:
  • v = ±ω√(A² − x²). At x = 0: vmax = ωA.
  • ± because the mass passes each x moving both ways.
Mission 2

Worked example

  • m = 0.50 kg on a spring, k = 200 N m⁻¹, amplitude 0.060 m.
  • Total = ½kA² = ½ × 200 × 0.060² = 0.36 J.
  • At x = 0.030 m: PE = ½ × 200 × 0.030² = 0.090 J → KE = 0.36 − 0.090 = 0.27 J.
  • Speed: ½ × 0.50 × v² = 0.27 → v = 1.0 m s⁻¹.
  • Check: ω = 20 rad s⁻¹ (= √(k/m)). v = 20 × √(0.060² − 0.030²) = 1.0 m s⁻¹. ✓
Quick check
?A mass of 0.25 kg on a spring of spring constant 16 N m⁻¹ oscillates with simple harmonic motion of amplitude 0.050 m. What is its speed when its displacement is 0.030 m?
Mission check

?A glider on an air track is attached between two springs and oscillates with simple harmonic motion of amplitude 0.10 m. Friction is negligible. At what distance from the equilibrium position are the glider's kinetic energy and the elastic potential energy of the system equal?
Mission 3

Mission 3: Why can small pushes, timed just right, build up a huge swing?

Make a guess: Why can small pushes, timed just right, build up a huge swing?

Mission 3

Free and forced oscillations

Free and forced oscillationspull,releaseFreeForcedsignalgeneratorvibrationgeneratortimeat f0, naturaltimeat f, the driverdisplacementdisplacement (steady)
  • Free oscillation: displace it, let go, no further force. It oscillates at its natural frequency, f0.
  • Forced oscillation: a periodic driving force keeps acting.
  • Once steady, a forced system oscillates at the driving frequency, not at f0.
Quick check
?A lightly damped mass–spring system has a natural frequency of 2.0 Hz. It is driven by a periodic force of constant amplitude with a frequency of 3.5 Hz. Which describes its oscillation once the amplitude has become steady?
Mission 3

Resonance

Resonance curveamplitudedriving frequencyf0resonancenot zeropush at the same pointof every cyclePushes at the natural frequency add energyevery cycle.
  • Resonance: driving frequency = natural frequency → maximum amplitude.
  • Why: each push is in step with the motion, so the driver does positive work on every cycle. Energy builds up.
  • Amplitude–driving frequency graph: small at low frequency, a peak at f0, then falls towards zero at high frequency.
  • The peak height is limited by damping: the amplitude stops growing when energy lost per cycle = energy supplied per cycle.
Quick check
?In its spin cycle, a washing machine's drum speeds up steadily. At one rotation rate the whole machine shakes violently; at higher rates it runs smoothly again. Why does it shake at that one rate?
Mission 3

Damping

Light, critical and heavy dampingdisplacementtimelight: decays inside the envelopecritical: back fastest, no overshootheavy (over-damping): creeps back slowly
  • Damping: a resistive force (air resistance, friction, a fluid) takes energy out of the oscillation. The energy ends up as thermal energy of the surroundings.
  • Undamped: kinetic ⇄ potential energy, total energy constant. Damped: total energy falls, so the amplitude falls.
  • Light damping: keeps oscillating; amplitude decays gradually; period almost unchanged.
  • Critical damping: returns to equilibrium in the shortest time, without oscillating.
  • Heavy damping (also called over-damping): no oscillation; creeps back more slowly than critical.
Quick check
Graph of displacement x (vertical axis) against t / s (horizontal axis marked 0, 2, 4, 6, 8). All three curves start at t / sx24680XYZ
?The graph shows displacement–time curves X, Y and Z for the same mass–spring system, released from rest at the same displacement with three different amounts of damping. Which statement about the curves is correct?
Mission 3

Damping changes the resonance curve

Damping and the resonance curveamplitudedriving frequencyf0lightmediumheavyMore damping: lower, broader peak,at a slightly lower frequency.
  • More damping:
    • lower peak (smaller maximum amplitude),
    • broader, flatter curve: the resonance is less sharp,
    • peak at a slightly lower frequency.
  • Light damping: tall, sharp peak, very close to f0.
  • Far from f0 (very low or very high driving frequency), damping makes little difference.
Quick check
?The same oscillator is driven by a periodic force of the same constant amplitude in two experiments, X and Y, with different damping. In X the maximum amplitude is 25 mm, at 5.00 Hz, and the amplitude falls to half this value at 4.82 Hz and 5.17 Hz. In Y the maximum amplitude is 3.4 mm, at 4.89 Hz, and the amplitude falls to half this value at 3.3 Hz and 6.1 Hz. Which conclusion do the data support?
Mission check

?A singer shatters a wine glass by singing one steady note close to it. Which condition is essential for this to happen?
Mission 4

Mission 4: Engineers add damping to bridges, cars and doors. How much damping is just right?

Make a guess: Engineers add damping to bridges, cars and doors. How much damping is just right?

Mission 4

Seeing resonance: Barton's pendulums

Barton's pendulumsdriver(heavy)Same length as the driver (same f0):largest amplitude.Light paper-cone pendulums, lengthsincreasing left to right.
  • One heavy driver pendulum and several light pendulums of different lengths, all hung from one string.
  • The driver forces every light pendulum at the driver's frequency.
  • The light pendulum of the same length as the driver (same f0) swings with the largest amplitude: resonance.
  • Make the light bobs from paper cones (more damping): every amplitude falls, and the "winner" stands out less. The resonance is less sharp.
Mission 4

Investigating damping of a spring

Investigating damping of a springmasscard discmotion sensor→ data logger−80−4004080displacement / mmtime80645141TTTEach peak = 0.8 × the one before. Peaksequally spaced: same period.Illustrative data.
  • Mass on a spring. Add a card disc to increase air resistance.
  • Record amplitude after each oscillation: a motion sensor and data logger, or video against a ruler.
  • Light damping: the amplitude falls by roughly the same fraction each cycle (an exponential-style decay).
  • Illustrative data: 80, 64, 51, 41 mm. Each is 0.8 × the one before.
  • Bigger card → bigger fraction lost each cycle.
Quick check
?A lightly damped mass–spring system is released with an amplitude of 60 mm. After one complete oscillation its amplitude is 45 mm. The amplitude falls by the same fraction in each oscillation. What is the amplitude after three complete oscillations?
Mission 4

Where the energy goes

Energy in dampingTotal oscillation energy (% of start)100%start64%cycle 141%cycle 226%cycle 3Amplitude × 0.8 each cycle, so energy × 0.8²= 0.64 (E ∝ A²).Lost energy → thermal energy in thesurroundings.
  • Damped: work done against resistive forces → thermal energy in the surroundings. Total energy falls, so A falls (energy ∝ amplitude²).
Quick check
?Damping reduces the amplitude of a mass–spring oscillator from 40 mm to 20 mm. What fraction of the original oscillation energy has been transferred to the surroundings?
Mission 4

Critical damping at work

Damping a car suspensioncar bodyspringshockabsorberbody heighttimeleveltoo little damping: keeps bouncingclose to critical: settles fastesttoo much damping: slow returnBody pushed up by a bump, then released.
  • Car suspension: spring + shock absorber (a damper: oil forced through small holes).
    • Too little damping: the car keeps bouncing after a bump.
    • Too much: the wheel cannot follow the road; bumps are passed straight to the car body.
    • Designed close to critical: returns to level quickly with little or no bounce.
  • Door closers: close without slamming or swinging past.
  • Analogue meters: the pointer settles on its reading quickly, without wobbling.
Mission 4

Designing against resonance

Footbridge fixesView along the bridge (deck end-on)sideways swaydamperssideways swaystiffening bracesFix 1: damp itenergy removedFix 2: move f0stiffer → higher f0
  • Avoid: bridges, buildings, machinery and vehicle parts must not have f0 near a driving frequency they meet (walkers, wind, engines, earthquakes).
  • Fix 1: damp it. Millennium Bridge (2000): dampers added under the deck; the sway stopped.
  • Fix 2: move f0. Stiffer structure → higher f0; added mass → lower f0.
  • Useful: tuning circuits (radio); musical instruments.
Mission 4

Resonance and stationary waves

Resonance of a string1st harmonic: f12nd harmonic: 2f13rd harmonic: 3f1vibration generatoramplitudedriving frequencyf12f13f1
  • A string (or air column) has many natural frequencies: its harmonics.
  • Drive a string with a vibration generator. At each harmonic, a large-amplitude stationary wave forms: resonance.
  • Between harmonics: only a small, messy vibration.
  • Resonance tube: an air column resonates when the tuning-fork frequency matches one of its natural frequencies; the sound becomes loud.
Quick check
?A car's wing mirror buzzes violently at one engine speed. A rubber damper is fitted to the mirror's mounting. What happens now as the engine passes that speed?
Mission check

?A seismometer has a heavy mass on a spring, with adjustable damping. After a sudden jolt, with the damping set low, the mass swings past its rest position and back several times before it settles. The damping is then increased in small steps. Which describes how the mass's motion changes?
Recap

The big ideas

Mission 1

  • T = 2π√(m/k); T = 2π√(l/g), for small angles.
  • Spring: no g, no amplitude. Pendulum: no mass, no (small) amplitude.
  • Plot T² against l (or m): gradient 4π²/g (or 4π²/k).

Mission 2

  • KE and PE swap twice per cycle; the total is constant if there is no damping. At ±A all PE; at equilibrium all KE.
  • Mass–spring: Etotal = ½kA²; PE = ½kx².
  • v = ±ω√(A² − x²); vmax = ωA.

Mission 3

  • A forced oscillator settles at the driving frequency; resonance (maximum amplitude) happens when the driving frequency equals the natural frequency.
  • More damping: lower, broader resonance peak at a slightly lower frequency. Light damping oscillates and decays; critical returns fastest without oscillating; heavy (over-) damping returns slowly.

Mission 4

  • Damping removes energy (E ∝ A²); light damping cuts the amplitude by roughly the same fraction each cycle. Suspensions, door closers and meters are damped close to critical.
  • Harmful resonance is prevented by adding damping or moving f0 away from the driving frequency.
  • Stationary waves are resonance at a harmonic.
🏆

Mini-lesson complete!

⭐⭐⭐

You've worked through SHM energy, pendulums and resonance for AQA A-level Physics. 🎉

  1. Mission 1Take a pendulum clock to the Moon. Does it run fast, run slow, or keep time?
  2. Mission 2A mass on a spring keeps stopping and starting again. Where is its energy at the instant it stops?
  3. Mission 3Why can small pushes, timed just right, build up a huge swing?
  4. Mission 4Engineers add damping to bridges, cars and doors. How much damping is just right?

Your stars: 0 / 0

📣 Smashed it? Share your score

Challenge a friend to beat your stars, or show a parent how you got on.

→ Back to A-Level Physics · AQA