← A-Level Physics · AQA · A-Level Physics revision
⭐ 0
AQA A-level Physics (7408) · 3.4 Mechanics and materials (part 4)
Mini-Lesson

Mechanics and materials (part 4)

5 missions. Guess, learn, then check. Your place is saved.

  1. Mission 1How could you test whether a crown is pure gold without damaging it?
  2. Mission 2Why are the markings on a spring weighing scale evenly spaced?
  3. Mission 3A thin steel wire and a thick steel cable carry the same load. Why does the wire stretch more?
  4. Mission 4Stretch a spring twice as far. Does it store twice the energy?
  5. Mission 5Bend a paperclip a little and it springs back. Bend it further and it stays bent. Why?
Mission 1

Mission 1: How could you test whether a crown is pure gold without damaging it?

Make a guess: How could you test whether a crown is pure gold without damaging it?

Mission 1

Density

Same material, different sizeWhole blockHalf of it128 g64 gmass16 cm³8 cm³volume8.0 g cm⁻³8.0 g cm⁻³densityCut in half: half the mass, half the volume,same density.
  • Density = mass per unit volume: ρ = m/V.
  • SI unit: kg m⁻³. Also common: g cm⁻³.
  • 1 g cm⁻³ = 1000 kg m⁻³. Water: about 1.0 g cm⁻³ = 1000 kg m⁻³.
  • Density belongs to the material, not the object. Cut a block in half: half the mass, half the volume, same ρ.
  • Rearranged: m = ρV and V = m/ρ.
Quick check
?The density of aluminium is 2.7 g cm⁻³. What is the volume, in m³, of an aluminium block of mass 0.081 kg?
Mission 1

Worked example

  • A brass cylinder: radius 1.0 cm, height 5.0 cm, mass 133 g.
  • V = πr²h = π × 1.0² × 5.0 = 15.7 cm³.
  • ρ = m/V = 133 ÷ 15.7 = 8.5 g cm⁻³.
  • In SI: 8.5 g cm⁻³ × 1000 = 8.5 × 10³ kg m⁻³.
  • Convert at the end, or work in kg and m³ throughout. Never mix g with m³.
Mission 1

Measuring density

Measuring densityRegular solidvernier callipers:repeat at several places0.00 gbalance zeroedfirstIrregular soliddisplacement canmeasuring cylinder:V = volume of waterdisplacedLiquidbalanceeye level with thebottom of themeniscusmass: empty cylinder,then with liquid
  • Mass: top-pan balance (zeroed).
  • Regular solid: measure dimensions with vernier callipers or a micrometer; repeat at several places; calculate V.
  • Irregular solid: sink it in a displacement can or measuring cylinder; V = volume of water displaced.
  • Liquid: mass of an empty measuring cylinder, then with liquid added; read V at the bottom of the meniscus, eye level.
  • Better: plot mass against volume for several readings. Gradient = ρ.
  • Cube of side L: % uncertainty in ρ = % in m + 3 × % in L.
Quick check
Graph of total mass m (g) of beaker and liquid on the vertical axis against volume V (cm³) of liquid in the beaker on thm / gV / cm³0408012016020024028050100150200250
?A student pours a liquid into a beaker in steps. After each step she records the volume V of liquid in the beaker and the total mass m of the beaker and liquid. The graph shows her results. What is the mass of 400 cm³ of this liquid?
Mission check

?A coin that looks like silver has a mass of 26.9 g. Lowered into a measuring cylinder of water, it raises the reading by 3.0 cm³. The table gives densities in kg m⁻³: aluminium 2.70 × 10³; copper 8.96 × 10³; silver 10.5 × 10³; lead 11.3 × 10³. Which metal is the coin most likely made of?
Mission 2

Mission 2: Why are the markings on a spring weighing scale evenly spaced?

Make a guess: Why are the markings on a spring weighing scale evenly spaced?

Mission 2

Hooke's law

Natural length and extensionnaturallengthextensionforceno load
  • Stretch a spring: the force it exerts is proportional to its extension.
  • This holds only up to a limit.
  • Extension = stretched length − original (natural) length. Not the whole length.
  • F = kΔL. k is the stiffness (or spring constant).
  • Unit of k: N m⁻¹. Larger k: stiffer spring.
  • Works for compression too: the extension is then the decrease in length.
Quick check
?In a lab, a student models a spring as a light spring that obeys Hooke's law. Which statement describes how the spring's force behaves in this model?
Mission 2

Worked example

  • A spring hangs with natural length 12.0 cm. A 4.0 N weight stretches it to 17.0 cm.
  • Extension = 17.0 − 12.0 = 5.0 cm = 0.050 m.
  • k = force ÷ extension = 4.0 ÷ 0.050 = 80 N m⁻¹.
  • Hang 6.0 N instead: extension = 6.0 ÷ 80 = 0.075 m = 7.5 cm.
  • New length = 12.0 + 7.5 = 19.5 cm. Always add the extension back to the natural length.
Mission 2

The force–extension graph

Force–extension graph beyond the limitextension / mforce / N0limit of proportionalityelastic limitgradient = kunloadingpermanent extension
  • Plot force against extension. Hooke's law: a straight line through the origin.
  • Gradient = k.
  • Beyond the limit of proportionality the line curves.
  • Below the elastic limit: remove the load and it returns to its original length.
  • Beyond the elastic limit: it is permanently stretched.
Quick check
Graph with F (N), the magnitude of the spring force, on the vertical axis and L (cm), the length of the spring, on the h0.51.01.501020F / NL / cm
?The graph shows the magnitude F of the force exerted by a light spring that obeys Hooke's law, as a function of the spring's length L, from its natural length to a length of 20 cm. What is the spring constant of the spring?
Mission check

?A spring that obeys Hooke's law is 15.0 cm long when it supports a 3.0 N load and 18.0 cm long when it supports a 6.0 N load. What is its natural (unloaded) length?
Mission 3

Mission 3: A thin steel wire and a thick steel cable carry the same load. Why does the wire stretch more?

Make a guess: A thin steel wire and a thick steel cable carry the same load. Why does the wire stretch more?

Mission 3

Stress and strain

Stress and strainBefore and after loadingforceoriginal lengthextensioncross-sectionalareaTensile stress = force ÷ cross-sectionalarea (Pa)Tensile strain = extension ÷ original length(no unit)Same load, thin and thick wiresame loadthin wiresmall area: largerstresssame loadthick cablelarge area: smallerstressNot to scale.
  • Tensile stress = force ÷ cross-sectional area. Unit: Pa (N m⁻²).
  • Tensile strain = extension ÷ original length. No unit (a ratio).
  • Stress = F/A; strain = ΔL/L.
  • Same load on a thinner wire → larger stress.
Mission 3

The Young modulus

Stress–strain graph and the Young modulusstress / Pastrain (no unit)0limit ofproportionalitysteelΔstrainΔstressrubber(small strains)Gradient of the straight part = Youngmodulus, EStraight from the origin: Hooke’s law holds.Not to scale: Young modulus of steel about 2× 10¹¹ Pa, of rubber about 10⁶ Pa.
  • Young modulus = tensile stress ÷ tensile strain. Unit: Pa.
  • E = (F/A) ÷ (ΔL/L) = FL/AΔL
  • Valid only where Hooke's law holds (up to the limit of proportionality).
  • It is the gradient of the straight part of a stress–strain graph.
  • It belongs to the material. The spring constant (Young modulus × area ÷ length) belongs to the object.
  • Steel: about 2 × 10¹¹ Pa. Rubber: about 10⁶ Pa.
Mission 3

Worked example

  • Steel wire: length 2.50 m, diameter 0.40 mm, load 20 N, E = 2.0 × 10¹¹ Pa. Extension?
  • A = π(d/2)² = π(0.20 × 10⁻³)² = 1.26 × 10⁻⁷ m². (Radius, not diameter.)
  • Stress = F/A = 20 ÷ 1.26 × 10⁻⁷ = 1.6 × 10⁸ Pa.
  • Strain = stress/E = 1.6 × 10⁸ ÷ 2.0 × 10¹¹ = 8.0 × 10⁻⁴.
  • Extension = strain × original length = 8.0 × 10⁻⁴ × 2.50 = 2.0 × 10⁻³ m (2.0 mm).
Quick check
?A metal wire of length 1.80 m and diameter 0.30 mm is loaded, and a graph of force F against extension is plotted. The straight part of the graph has a gradient of 7.9 × 10³ N m⁻¹. What is the Young modulus of the metal?
Mission 3

Measuring the Young modulus

Measuring the Young modulus(a) Long wire over a pulleyclampmassesmarker against a mm scaleoriginal length: clamp to marker(b) Searle's apparatusreferencewiretest wirespirit levelmicrometer orvernier: extensionread relative tothe reference wireconstant loadload added in stepsDiameter: micrometerseveral places and directionswirewear eye protection:the wire may snapNot to scale.
  • A long, thin wire: a large extension from a modest load, so its percentage uncertainty is small.
  • Clamp one end. Run it over a pulley, or hang it beside an identical reference wire (Searle's apparatus).
  • Diameter: micrometer, several places and directions; average. Length: metre rule to the marker.
  • Add masses in steps; read the extension from a marker against a scale (or a vernier). Unload to check it returns: still elastic.
  • Plot force against extension. Young modulus = gradient × original length ÷ area. (Or plot stress against strain: gradient = Young modulus.)
  • The reference wire cancels temperature changes and sag of the support. Wear eye protection: the wire may snap.
Quick check
?A student repeats the Young modulus experiment with the same loads on a wire of the same metal and diameter, but only one tenth as long. The extension is read with the same scale. What is the main effect?
Mission check

?Two cables are made of the same aluminium alloy and carry the same load. Cable Q is 3 times as long as cable P and has 3 times its diameter. Both obey Hooke's law. What is the extension of Q divided by the extension of P?
Mission 4

Mission 4: Stretch a spring twice as far. Does it store twice the energy?

Make a guess: Stretch a spring twice as far. Does it store twice the energy?

Mission 4

Work done stretching = area

  • Stretching a spring or wire takes work: force × distance moved.
  • The force is not constant: it rises from 0 to its final value as the extension grows from 0.
  • Work done = area under the force–extension graph.
  • In the elastic region this work is stored as elastic strain energy (also called elastic potential energy). Unload, and you get it back.
Mission 4

Energy stored = ½ × force × extension

Energy stored: area under a force–extension lineforce / Nextension / mFΔL0F/2average forceenergy stored = ½FΔLArea under the line = work done = triangle,½ × base × height.
  • Hooke's law region: the graph is a straight line, so the area is a triangle.
  • Energy stored = ½FΔL (F = final force, ΔL = extension).
  • Use F = kΔL: E = ½(kΔL)ΔL = ½k(ΔL)².
  • Double the extension → four times the energy.
Mission 4

Worked example

  • Spring: k = 80 N m⁻¹, stretched by 0.050 m.
  • Force: F = kΔL = 80 × 0.050 = 4.0 N.
  • Energy: E = ½FΔL = ½ × 4.0 × 0.050 = 0.10 J.
  • Check: ½k(ΔL)² = ½ × 80 × 0.050² = 0.10 J.
  • Stretched to 0.10 m: ½ × 80 × 0.10² = 0.40 J. Twice the extension, four times the energy.
  • Not ½ × 4.0 × 0.10: the force is now 8.0 N, not 4.0 N.
Quick check
?A steel wire obeys Hooke's law. A tension of 60 N gives an extension of 1.2 mm. How much elastic strain energy does the wire store?
Mission 4

Curved graphs: use the area

Area under a curved force–extension graphforce / Nextension / m0limit ofproportionalitybreaksarea under the curve =work doneEnergy of one square = force per square ×extension per square. Count squares underthe curve (part squares: estimate).
  • Beyond the limit of proportionality the graph curves. ½ × force × extension no longer works.
  • Find the area: count squares, or split it into triangles and trapezia.
  • Energy of one square = (force per square) × (extension per square).
  • Plastic region (the sample stays permanently stretched when unloaded): the work done is not all stored. Most becomes internal energy (the sample warms); the wire stays longer.
  • Breaking stress: the tensile stress at which the sample breaks. Area up to the break = work done to break the sample.
Quick check
Idealised force–extension graphforce / Nextension / mm02468100102030Idealised force–extension graph for a metalwire.
?The graph shows an idealised force–extension graph for a metal wire. The force rises linearly from 0 to 30 N over the first 4.0 mm, then stays at 30 N as the extension increases to 10.0 mm. How much work is done stretching the wire to 10.0 mm?
Mission 4

Spring energy becomes kinetic and potential energy

Spring launcher energy transfersLauncher fired straight up (ignoring airresistance)compressed,ball at restleavingthe springv = 0at the top0.25 J0.25 J0.25 Jelastickineticgravitational potentialTotal energy the same at every stage (nolosses). Top: 1.3 m above the release point.Not to scale.
  • A launcher spring, k = 200 N m⁻¹, compressed by 0.050 m, fires a 0.020 kg ball.
  • Stored: E = ½k(ΔL)² = ½ × 200 × 0.050² = 0.25 J.
  • Fired horizontally, all to kinetic energy: ½mv² = 0.25 → v = √(2 × 0.25 ÷ 0.020) = 5.0 m s⁻¹.
  • Fired straight up, all to gravitational potential energy at the top: Δh = 0.25 ÷ (0.020 × 9.81) = 1.3 m above the release point.
  • Real launchers lose some energy to friction and air resistance: the ball rises less.
Quick check
?The spring in a toy dart launcher has a spring constant of 400 N m⁻¹. It is compressed by 0.030 m and then released, firing a dart of mass 0.012 kg horizontally. All the elastic potential energy is transferred to the dart's kinetic energy. What is the speed of the dart?
Mission 4

Energy to deform: crumple zones

Crumple zones: same energy, smaller forceBarrier test: before and afterbarriercrumple zonecrumpled: permanent deformationSame energy, different distanceaverage force / Ndistance / m00.10.20.30.40.52.0 × 10⁵1.0 × 10⁶rigid front, 0.10 mcrumple zone, 0.50 mEqual areas: work done = average force ×distance = kinetic energy ≈ 1.0 × 10⁵ J(1200 kg car at 13 m s⁻¹). Illustrative.
  • A crash must remove the car's kinetic energy.
  • Crumple zones deform plastically: the energy goes into permanent deformation and internal energy, not into a bounce back.
  • Work done = average force × crumple distance. Longer crumple distance → smaller average force on the occupants.
  • Illustrative: 1200 kg car at 13 m s⁻¹: Ek = ½ × 1200 × 13² ≈ 1.0 × 10⁵ J. Crumpling 0.50 m: average force ≈ 2.0 × 10⁵ N. A rigid front stopping in 0.10 m: ≈ 1.0 × 10⁶ N.
  • Design choices weigh up occupant safety, pedestrian safety (bonnets that deform), mass and fuel use.
Quick check
?A car's crumple zone is redesigned so that, in the same crash test at the same speed, the front of the car crumples twice as far before the car stops. Assume all the kinetic energy is transferred while the front crumples. What happens to the average force on the car during the crash?
Mission check

?A spring obeys Hooke's law. When it is compressed by 3.0 cm it stores 0.45 J. How much energy does it store when it is compressed by 4.5 cm?
Mission 5

Mission 5: Bend a paperclip a little and it springs back. Bend it further and it stays bent. Why?

Make a guess: Bend a paperclip a little and it springs back. Bend it further and it stays bent. Why?

Mission 5

Force–extension graph of a metal wire

Force–extension graph of a metal wireforce / Nextension / m0P: limit of proportionalityEL: elastic limitbreakselasticplasticStraight up to P (Hooke’s law). Elastic upto EL; beyond it, plastic. Sketch, not toscale.
  • Limit of proportionality (P): up to here, extension ∝ force (Hooke's law). Straight line.
  • Elastic limit (EL): the largest force after which the wire still returns to its original length.
  • Beyond the elastic limit: plastic region. Then the wire breaks.
Mission 5

Elastic and plastic

Loading and unloading a metal wireforce / Nextension / m0PELloadingunloading:parallel to thestraight startpermanent extensionLoaded past the elastic limit (EL), the wirestays permanently longer. Sketch, not toscale.
  • Elastic deformation: removed load → returns to its original length.
  • Plastic deformation: removed load → permanent extension.
  • The limit of proportionality and the elastic limit are different points.
  • A metal loaded into the plastic region unloads along a line parallel to the original straight line. It ends up permanently longer.
Quick check
?A wire is loaded until its force–extension graph has just started to curve. The load is then removed, and the wire returns exactly to its original length. What can you conclude about the load?
Mission 5

Three kinds of stress–strain curve

Brittle, ductile and polymeric stress–strain curvesductile(copper)stressstrainbreaking stressnecks, then fractureslong plastic regionbrittle(glass)strainfracturenoplasticregionpolymeric(rubber)strainvery largestrainEach graph has its own stress and strainscale: rubber’s strains are far larger.Sketches, not to scale.
  • Ductile (copper, mild steel): straight, then a long plastic region. Can be drawn into wires. Thins (necks) before it breaks.
  • Brittle (glass, cast iron): straight right up to fracture. No plastic region. Snaps suddenly.
  • Polymeric (rubber): low stiffness, very large strain, curved. (Polythene: stretches plastically, cold-drawing.)
Quick check
?Two materials are tested to destruction. Material X: the stress–strain graph is straight all the way to fracture, at a strain of 0.001. Material Y: the graph is straight to a strain of 0.002, then curves and continues to a strain of 0.40 before fracture. Which describes the materials?
Mission 5

Energy and permanent deformation

Work done in plastic deformationforce / Nextension / m0recoverednot recoveredArea under the loading curve = work done.Only the triangle under the unloading lineis recovered; the rest heats the materialand deforms it permanently. Sketch.
  • Area under a force–extension graph = work done deforming the sample.
  • Elastic region: that energy is stored and given back on unloading.
  • Plastic region: much of the work done is not recovered. It heats the material and rearranges it permanently.
  • Design for safety: crumple zones deform plastically, absorbing kinetic energy in a crash.
Mission check

?A copper wire is loaded beyond its elastic limit. At the maximum load of 30 N its extension is 6.0 mm. The straight first part of its force–extension graph has a gradient of 20 N per mm. The load is then removed completely. What is the permanent extension of the wire?
Recap

The big ideas

Mission 1

  • ρ = m/V, in kg m⁻³ (1 g cm⁻³ = 1000 kg m⁻³); density belongs to the material, not the object.
  • Measure m with a balance and V from dimensions or displacement; the gradient of m against V gives ρ.

Mission 2

  • Extension (not length) is proportional to force: gradient of the force–extension graph = k, in N m⁻¹.
  • This holds up to the limit of proportionality.
  • Beyond the elastic limit the stretch is permanent.

Mission 3

  • Stress = F/A (Pa); strain = extension/original length (no unit); Young modulus = stress/strain, the gradient of the linear part of a stress–strain graph.
  • Measure the Young modulus with a long, thin wire: Young modulus = gradient of force against extension × original length ÷ area.

Mission 4

  • Elastic strain energy = area under the force–extension graph = ½FΔL = ½k(ΔL)² while Hooke's law holds; for a curved graph, find the area.
  • Crumple zones absorb kinetic energy by plastic deformation; a longer crumple distance gives a smaller average force.

Mission 5

  • Limit of proportionality: end of the straight line. Elastic limit: beyond it, deformation is plastic and permanent.
  • Ductile: long plastic region; brittle: straight to fracture; polymeric: large strain, low stiffness.
🏆

Mini-lesson complete!

⭐⭐⭐

You've worked through Mechanics and materials (part 4) for AQA A-level Physics. 🎉

  1. Mission 1How could you test whether a crown is pure gold without damaging it?
  2. Mission 2Why are the markings on a spring weighing scale evenly spaced?
  3. Mission 3A thin steel wire and a thick steel cable carry the same load. Why does the wire stretch more?
  4. Mission 4Stretch a spring twice as far. Does it store twice the energy?
  5. Mission 5Bend a paperclip a little and it springs back. Bend it further and it stays bent. Why?

Your stars: 0 / 0

📣 Smashed it? Share your score

Challenge a friend to beat your stars, or show a parent how you got on.

→ Back to A-Level Physics · AQA