← A-Level Chemistry · OCR · A-Level Chemistry revision
⭐ 0
OCR A-level Chemistry A (H432) · Module 3 - 3.2 Physical chemistry
Mini-Lesson

Physical chemistry

7 missions. Guess, learn, then check. Your place is saved.

  1. Mission 1A speed camera clocks a car at one instant. How do you clock a reaction at one instant?
  2. Mission 2When a cold pack goes cold, has the chemical inside lost energy or gained it?
  3. Mission 3If breaking bonds takes in energy, how can burning a fuel give energy out?
  4. Mission 4Why can a cloud of flour dust explode, when a heap of flour only smoulders?
  5. Mission 5Where does half the energy go when you burn a fuel under a can of water?
  6. Mission 6Carbon always burns partly to CO2. So how do we know ΔH for making carbon monoxide?
  7. Mission 7Carbon and hydrogen don't combine cleanly to make methane. So how does the data booklet know its enthalpy of formation?
Mission 1

Mission 1: A speed camera clocks a car at one instant. How do you clock a reaction at one instant?

Make a guess: A speed camera clocks a car at one instant. How do you clock a reaction at one instant?

Mission 1

What rate means

  • Rate of reaction: the change in concentration of a reactant or product per unit time.
  • Units: mol dm⁻³ s⁻¹.
  • Reactant concentrations fall; product concentrations rise. Rate is quoted as a positive value.
  • Other measured quantities work too: gas volume per second, mass lost per second.
Quick check
?Hydrogen peroxide decomposes: 2H2O2(aq) → 2H2O(l) + O2(g). Which quantity is the rate of this reaction at a particular moment?
Mission 1

Following a reaction as it happens

Three ways to follow a reaction1 Gas volume0204060cm³gas syringe2 Mass lossCO2 outgcotton wool:CO2 escapes,acid sprayis stopped3 Colour: colorimeterlampfiltercuvettedetector4 Calibration curveAbsorbanceConcentration / mol dm−3points: standardsolutions, known conc.
  • Gas volume: collect the gas in a gas syringe; read the volume at set times.
  • Mass loss: a gas escapes from a flask on a balance, e.g. CO2 from marble chips and acid.
  • Colour: a coloured reactant or product is followed with a colorimeter.
  • These are continuous monitoring methods: many readings from one run.
  • Change one variable; keep everything else the same.
Mission 1

Colorimetry

  • Light passes through the solution; a coloured species absorbs some of it.
  • Choose a filter of the colour the species absorbs (the complementary colour).
  • Make a calibration curve: absorbance of solutions of known concentration.
  • Read each absorbance during the reaction; convert it to concentration from the curve.
  • Good for reactions of Br2, I2 or MnO4⁻: nothing is removed from the mixture.
Mission 1

Clock reactions: the initial-rate method

Clock methodsDisappearing crossIodine clockclearcloudy(sulfur)colourlessblue-blacktime t untilcross hiddentime t untilblue-black1/tConcentrationrate ∝ 1/tvalid only whilelittle hasreacted
  • Time how long a fixed, small amount of reaction takes: t.
  • Early on, the rate hardly changes, so initial rate ∝ 1/t.
  • Disappearing cross: thiosulfate + acid forms a sulfur precipitate; time until the cross is hidden.
  • Iodine clock: time until a sudden blue-black colour with starch.
  • Repeat with different starting concentrations: one run per concentration.
Quick check
?A student reacts 0.10 g of magnesium ribbon with excess dilute hydrochloric acid: Mg(s) + 2HCl(aq) → MgCl2(aq) + H2(g). Which method is least suitable for measuring the rate of this reaction?
Mission 1

Average rate or rate at an instant

Average rate and rate at an instant on a product-time curveAmount of productTimePinitial raterate at Paverage rate
  • Average rate = total change ÷ total time: the gradient of a straight line between two points.
  • Rate at an instant = gradient of the tangent to the curve at that time.
  • Initial rate: the tangent at t = 0, where the curve is steepest.
  • The curve flattens as reactants are used up: the rate falls.
Mission 1

Worked example: drawing a tangent

Worked tangent: mass of CO2 lost against time01002003000.00.51.01.52.0Mass of CO2 lost / gTime / sPΔx = 120 sΔy = 1.46 g2.00 gP on the curve = (60 s, 1.19 g)tangent: (0 s, 0.46 g) to (120 s, 1.92 g)gradient = 1.46 ÷ 120 = 0.0122 g s−1
  • Marble chips + acid: mass of CO2 lost against time. At 60 s, 1.19 g has been lost.
  • Draw the tangent at 60 s. It passes through (0 s, 0.46 g) and (120 s, 1.92 g).
  • Rate = (1.92 − 0.46) g ÷ (120 − 0) s = 1.46 ÷ 120 = 0.0122 g s⁻¹.
  • Average over the first 60 s: 1.19 ÷ 60 = 0.0198: larger, because the reaction was faster early on.
  • Read two far-apart points on the tangent, not on the curve.
Quick check
?Magnesium ribbon reacts with excess hydrochloric acid, and the hydrogen is collected in a gas syringe. A graph of the volume of hydrogen (y-axis, cm³) against time (x-axis, s) is a curve that is steep at first, becomes less steep and levels off at 60 cm³ at 100 s. The curve passes through the point (20 s, 34 cm³). A tangent drawn to the curve at t = 20 s passes through the points (0 s, 10 cm³) and (40 s, 58 cm³). What is the rate of reaction at t = 20 s?
Calculate
?Bromine reacts with methanoic acid: Br2(aq) + HCOOH(aq) → 2HBr(aq) + CO2(g). A graph of [Br2] against time starts at 0.0130 and curves downwards, passing through (80 s, 0.0087). A tangent drawn at t = 80 s passes through (0 s, 0.0122) and meets the time axis at 280 s.
  • Concentrations in mol dm⁻³. Calculate the rate at t = 80 s, in units of 10⁻⁵ mol dm⁻³ s⁻¹.
Mission check

?Hydrogen peroxide decomposes on a catalyst, and the oxygen is collected in a gas syringe. The volume–time curve passes through (30 s, 41.9). The tangent drawn at t = 30 s passes through (0 s, 20.2) and (60 s, 63.6). At 60 s the curve itself reads 54.6. What is the rate of reaction at exactly t = 30 s?
  • Volumes in cm³; rates in cm³ s⁻¹.
Mission 2

Mission 2: When a cold pack goes cold, has the chemical inside lost energy or gained it?

Make a guess: When a cold pack goes cold, has the chemical inside lost energy or gained it?

Mission 2

System and surroundings

System and surroundingsairenergybulb measuresthe surroundingssystemsystem: the reacting chemicalssurroundings: water, beaker, thermometer, air
  • The system: the reacting chemicals, reactants and products.
  • The surroundings: everything else, water, container, thermometer, air.
  • Energy moves between them; the total is conserved.
  • A thermometer in the solution reads the surroundings, not the chemicals.
Mission 2

Heat is not temperature

  • Heat: energy transferred because of a temperature difference, in joules.
  • Temperature: a measure of the average kinetic energy of the particles (in kelvin, proportional to it).
  • A bath and a cup of water at 40 °C have the same temperature.
  • The bath can give out far more heat as it cools: many more particles.
Quick check
?Which statement correctly describes the temperature of a substance?
Mission 2

Exothermic and endothermic

Exothermic and endothermic reactionsExothermicsystemEnergy passes out of the systemSurroundingswarm upΔH < 0EndothermicsystemEnergy passes into the systemSurroundingscool downΔH > 0
  • Exothermic: energy passes from system to surroundings. Surroundings warm. ΔH negative.
  • Endothermic: energy passes from surroundings to system. Surroundings cool. ΔH positive.
  • ΔH describes the system. Always write its sign.
  • Enthalpy change, ΔH: the heat energy change measured at constant pressure.
  • A cold pack: the dissolving chemical gains energy from the water and your hand.
Mission 2

ΔH for an equation, and standard conditions

  • Enthalpy change of reaction, ΔrH: the enthalpy change for the amounts in a stated equation, in kJ mol⁻¹.
  • Standard conditions: 100 kPa and a stated temperature, usually 298 K.
  • Standard enthalpy change, ΔH⦵: measured under standard conditions, every substance in its standard state (its normal state under those conditions).
  • More on standard states and definitions in Mission 7.
Quick check
?A mixture of iron and sulfur must be heated strongly before it reacts. Once started, it glows red-hot with no further heating. What does this show?
Mission 2

Breaking takes in, making gives out

  • Breaking bonds takes in energy: endothermic.
  • Making bonds gives out energy: exothermic.
  • Bond making releases more than bond breaking takes in → exothermic overall. Less → endothermic.
  • The numbers come in Mission 3.
Mission 2

Enthalpy level diagrams

Enthalpy level diagramsExothermicenthalpyCH₄(g) + 2O₂(g)CO₂(g) + 2H₂O(l)ΔH negativeEndothermicenthalpy2NO(g)N₂(g) + O₂(g)ΔH positive
  • y-axis: enthalpy. Two levels: reactants and products, each labelled with formulae.
  • One vertical arrow, from reactants to products, labelled ΔH with its sign.
  • Products lower: exothermic, ΔH negative. Products higher: endothermic, ΔH positive.
Mission 2

Reaction profiles and activation energy

Reaction profilesenthalpyprogress of reactionExothermicEaΔHreactantsproductsenthalpyprogress of reactionEndothermicEaΔHreactantsproducts
  • y-axis: enthalpy. x-axis: progress of reaction. Not time.
  • A hump between reactants and products: the energy barrier.
  • Activation energy, Ea: the minimum energy needed for reaction; arrow from the reactant level up to the top of the hump.
  • ΔH: from the reactant level to the product level.
  • Exothermic and endothermic reactions both have a barrier.
  • OCR calls this an enthalpy profile diagram.
Quick check
?An enthalpy profile for a reaction shows, relative to the same zero, the reactants at 150 kJ mol⁻¹, the top of the energy barrier at 280 kJ mol⁻¹ and the products at 40 kJ mol⁻¹. What is ΔH for the reaction?
Quick check
?Which sketch is a correctly labelled profile for an endothermic reaction?
Mission check

?Hydrated barium hydroxide and ammonium chloride, both solids, are mixed in a flask standing on a wet wooden block. Within a minute the water under the flask freezes, sticking the flask to the block. Which statement about the reacting chemicals is correct?
Mission 3

Mission 3: If breaking bonds takes in energy, how can burning a fuel give energy out?

Make a guess: If breaking bonds takes in energy, how can burning a fuel give energy out?

Mission 3

Breaking takes in, forming gives out

  • Breaking a bond is endothermic: energy is absorbed.
  • Forming the same bond releases the same amount: exothermic.
  • Bonds never release energy as they break.
  • Exothermic overall: the bonds formed are stronger in total than those broken.
Mission 3

Bond enthalpy

  • Bond enthalpy: energy needed to break 1 mol of a bond, with all species gaseous. Always positive.
  • Average bond enthalpy: the energy needed to break 1 mol of a given bond in gaseous molecules, averaged over many different compounds.
  • Larger value → stronger bond.
Mission 3

Worked example: burning methane

Bond-enthalpy energy diagram for burning methaneC + 4H + 4O(gaseous atoms)CH₄(g) +2O₂(g)CO₂(g) +2H₂O(g)+2652 kJbreak:1656 + 996−3460 kJform:1608 + 1852net−808 kJ
  • ΔH = Σ(bonds broken) − Σ(bonds formed). Draw the structures; count every bond.
  • CH4(g) + 2O2(g) → CO2(g) + 2H2O(g)
  • Values given / kJ mol⁻¹: C–H 414, O=O 498, C=O 804, O–H 463.
  • Broken: 4 C–H + 2 O=O = 1656 + 996 = 2652 kJ.
  • Formed: 2 C=O + 4 O–H = 1608 + 1852 = 3460 kJ.
  • ΔH = 2652 − 3460 = −808 kJ mol⁻¹. Forming gives out more than breaking takes in.
Quick check
?Why is the C–H bond enthalpy in a table of bond enthalpies described as an average value?
Calculate
?Calculate ΔH for N2(g) + 3H2(g) → 2NH3(g).
  • Bond enthalpies / kJ mol⁻¹: N≡N 945, H–H 436, N–H 391. Give ΔH in kJ mol⁻¹.
kJ mol⁻¹
Mission 3

Why it is only an estimate

  • Values are averages over many compounds. The real bond in your molecule may differ.
  • They apply only to gases. If a substance is liquid or solid, the energy to change state is left out.
  • So a bond-enthalpy ΔH is an estimate.
  • Methane: −808 estimated; −890 kJ mol⁻¹ measured, with liquid water.
Quick check
?Using average bond enthalpies (C–H 414, O=O 498, C=O 804, O–H 463 kJ mol⁻¹), a student calculates ΔH = −808 kJ mol⁻¹ for CH4(g) + 2O2(g) → CO2(g) + 2H2O(g). The experimental enthalpy change for burning methane under standard conditions (100 kPa, 298 K) is −890 kJ mol⁻¹. Which statement explains why the experimental value is more exothermic than the calculated one?
Mission 3

Working backwards to a bond enthalpy

  • H2(g) + Br2(g) → 2HBr(g), ΔH = −103.5 kJ mol⁻¹.
  • Given: H–H 436, Br–Br 193 kJ mol⁻¹. Find H–Br, x.
  • Broken − formed = ΔH: (436 + 193) − 2x = −103.5
  • 2x = 629 + 103.5 = 732.5
  • x = 366 kJ mol⁻¹. Two H–Br bonds form, so divide by 2.
Quick check
?CH4(g) + Cl2(g) → CH3Cl(g) + HCl(g), ΔH = −99 kJ mol⁻¹. Bond enthalpies / kJ mol⁻¹: C–H 413, Cl–Cl 243, H–Cl 432. What value for the C–Cl bond enthalpy do these data give?
Mission check

?Both these reactions are exothermic, by very different amounts: H2(g) + I2(g) → 2HI(g) and H2(g) + F2(g) → 2HF(g). Which statement explains why the fluorine reaction gives out far more energy?
  • Bond enthalpies / kJ mol⁻¹: H–H 436, I–I 151, F–F 158, H–I 299, H–F 568.
Mission 4

Mission 4: Why can a cloud of flour dust explode, when a heap of flour only smoulders?

Make a guess: Why can a cloud of flour dust explode, when a heap of flour only smoulders?

Mission 4

Collision theory

Collision theory: energy and orientationGentle collisionXYZXYZbounce apartXYZE < Ea: no reactionHard collisionXYZXYZbonds rearrangeXYZE ≥ Ea: reaction
  • Particles must collide to react. The collision starts the breaking and making of bonds.
  • The collision needs energy at least equal to the activation energy, Ea.
  • Activation energy: the minimum energy that colliding particles need for a reaction to take place.
  • Most collisions do not react: their energy is less than Ea, so the particles just bounce apart.
Quick check
?In a mixture of two gases at room temperature, each molecule collides with others billions of times every second, yet the reaction between them is slow. Why do most of these collisions not lead to a reaction?
Mission 4

Concentration, pressure, surface area

What changes the collision frequencyHigher concentrationlowhighHigher gas pressurelarge volumesmall volumeLarger surface areaone lumpsame mass, small pieces
  • Higher concentration: more particles per unit volume → more frequent collisions.
  • Higher gas pressure: the same particles are squeezed closer → more frequent collisions.
  • Larger surface area of a solid: more particles exposed → more frequent collisions.
  • These change how often particles collide, not the energy of each collision.
  • So more successful collisions per second: a faster rate.
Quick check
?Hydrogen iodide decomposes: 2HI(g) → H2(g) + I2(g). A sample of hydrogen iodide is compressed to half its volume at constant temperature. What is the effect on the rate of reaction, and why?
Mission 4

Temperature

  • Higher temperature: particles move faster, with more kinetic energy.
  • Main effect: a much larger fraction of collisions have energy ≥ Ea.
  • Smaller effect: collisions are also a little more frequent.
  • So a small rise in temperature can give a large rise in rate.
  • A later mission shows this on the Maxwell–Boltzmann distribution.
Mission 4

Catalysts

Energy profile with and without a catalystEnthalpy profile diagramEnergyProgress of reactionEaEa(cat)ΔHReactantsProductsno catalystwith catalyst
  • A catalyst increases the rate of a reaction without being used up by the overall reaction.
  • It provides an alternative route with a lower activation energy.
  • So, at the same temperature, more collisions have E ≥ Ea. ΔH is unchanged.
Quick check
?Which statement explains how a catalyst increases the rate of a reaction at constant temperature?
Mission 4

Frequency or energy?

ChangeCollisions per secondFraction with E ≥ Ea
Higher concentrationmoresame
Higher gas pressuremoresame
Larger surface areamoresame
Higher temperaturea few moremany more
Catalyst addedsamemore (lower Ea)
  • Rate depends on the number of successful collisions per second.
Mission check

?A glowing splint only smoulders in air, but bursts into flame when it is lowered into a gas jar of pure oxygen at the same temperature and pressure. Air is about 21% oxygen. Which explanation is correct?
Mission 5

Mission 5: Where does half the energy go when you burn a fuel under a can of water?

Make a guess: Where does half the energy go when you burn a fuel under a can of water?

Mission 5

Measuring an enthalpy change

Two calorimetersReaction in solutionthermometergives ΔTlidpolystyrene cupbeakerstirrermm = mass of the solutionBurning fuelmthermometercopper canwaterdraught shieldspirit burnerm = mass of the waterheat to water
  • Solutions: react in a polystyrene cup with a lid, stirrer and thermometer.
  • Combustion: a spirit burner heats a known mass of water in a copper can.
  • Record the temperature before, then at regular intervals after.
  • Temperature rises: the process gave out energy, exothermic. Falls: it took energy in, endothermic.
  • Some ΔH values can't be measured in one step. Measure two reactions that can be, then combine them with Hess's law (see Mission 6).
Mission 5

q = mcΔT

Two calorimetersReaction in solutionthermometergives ΔTlidpolystyrene cupbeakerstirrermm = mass of the solutionBurning fuelmthermometercopper canwaterdraught shieldspirit burnerm = mass of the waterheat to water
  • q = mcΔT, with q in joules.
  • m: mass of the water or solution whose temperature changes, in g. Not the reactant's mass.
  • c: specific heat capacity; water 4.18 J g⁻¹ K⁻¹ (given in questions).
  • ΔT: the temperature change. Same in K and °C; never add 273.
  • Dilute solutions: take density 1.00 g cm⁻³ and c of water.
Mission 5

From q to ΔH

  • ΔH = −q ÷ n. n: amount of the limiting reactant, in mol (for a 1 : 1 equation).
  • Divide q by 1000 to get kJ.
  • The minus sign: the surroundings gain q, so the system loses it.
  • Temperature rise → ΔH negative. Fall → ΔH positive.
  • Final answer: sign, value, units, e.g. −201 kJ mol⁻¹.
Quick check
?50.0 cm³ of 1.00 mol dm⁻³ HCl(aq) is placed in a polystyrene cup and 25.0 cm³ of 1.00 mol dm⁻³ NaOH(aq) is added. The temperature of the mixture rises by 4.50 °C. HCl(aq) + NaOH(aq) → NaCl(aq) + H2O(l). Assume that the solutions have a density of 1.00 g cm⁻³ and a specific heat capacity of 4.18 J g⁻¹ K⁻¹. What is ΔH for the reaction?
Mission 5

Worked example

Temperature against time, zinc and copper(II) sulfate024681020222426283032Temperature / °CTime / minzinc addedΔT= 9.60 K31.00 °C30.4021.40 °Creadingsextrapolated lineillustrative data
  • Excess zinc powder is added to copper(II) sulfate solution: Zn(s) + CuSO4(aq) → ZnSO4(aq) + Cu(s).
  • 50.0 cm³ of 0.200 mol dm⁻³ CuSO4(aq).
  • 1. ΔT from the graph, corrected for heat loss (how: next screen): 31.00 − 21.40 = 9.60 °C (= 9.60 K).
  • 2. q = 50.0 × 4.18 × 9.60 = 2006 J = 2.006 kJ.
  • 3. n(CuSO4) = 0.0500 × 0.200 = 0.0100 mol. Zinc is in excess, so CuSO4 is limiting.
  • 4. ΔH = −2.006 ÷ 0.0100 = −201 kJ mol⁻¹.
Mission 5

Finding the true ΔT

Temperature against time, zinc and copper(II) sulfate024681020222426283032Temperature / °CTime / minzinc addedΔT= 9.60 K31.00 °C30.4021.40 °Creadingsextrapolated lineillustrative data
  • Heat is exchanged with the air while the reaction is still going.
  • So the highest (or lowest) reading falls short of the true change.
  • Plot temperature against time. Extrapolate the line after the highest (or lowest) reading back to the time of mixing.
  • ΔT = extrapolated value − starting temperature.
Quick check
?Why is the line after the highest reading extrapolated back to the time of mixing?
Calculate
?1.00 g of iron powder is added to 50.0 g of copper(II) sulfate solution, an excess, in a polystyrene cup. Fe(s) + CuSO4(aq) → FeSO4(aq) + Cu(s). The corrected temperature rise is 12.5 °C. Calculate ΔH for the reaction.
  • Data: Ar Fe = 55.8; c = 4.18 J g⁻¹ K⁻¹. The CuSO4(aq) is 50.0 cm³ of 1.00 mol dm⁻³.
kJ mol⁻¹
Mission 5

Enthalpy change of neutralisation

  • ΔneutH: the enthalpy change when 1 mol of water is formed in a neutralisation reaction (standard value: under standard conditions).
  • Method: acid in the cup, record its temperature, add alkali, stir, record the highest temperature.
  • n = amount of water formed, not of acid or alkali.
  • Strong acid + strong alkali: nearly the same value every time. It is always H⁺(aq) + OH⁻(aq) → H2O(l).
Quick check
?A spirit burner containing ethanol, C2H5OH, is used to heat 150.0 g of water in a copper can. Burning 0.920 g of ethanol raises the temperature of the water from 19.0 °C to 40.5 °C. Use c(water) = 4.18 J g⁻¹ K⁻¹ and Ar values H 1.01, C 12.01, O 16.00. What value of ΔH for the combustion of ethanol do these results give?
Mission 5

Why the measured value falls short

  • Accepted value for ethanol: −1367 kJ mol⁻¹. The can gave −675: about half.
  • The missing energy was not destroyed. It heated the air and the can, not the water.
  • Some ethanol burns incompletely (soot on the can); some evaporates from the wick.
  • Assumptions: all the heat reaches the water; the apparatus absorbs none; solutions behave like water.
  • Reduce losses: draught shield, lid, insulation, burner close to the can.
  • Heat loss makes a measured exothermic ΔH less negative.
Mission check

?A student measures the enthalpy change when potassium chloride dissolves in water. The temperature falls. The student uses a thin glass beaker with no lid instead of an insulated cup. How does the student's value of ΔH compare with the accepted value?
Mission 6

Mission 6: Carbon always burns partly to CO2. So how do we know ΔH for making carbon monoxide?

Make a guess: Carbon always burns partly to CO2. So how do we know ΔH for making carbon monoxide?

Mission 6

Hess's law

Hess's law: two routesABCΔH1ΔH2ΔH3ΔH1 = ΔH2 + ΔH3same start, same end, same total
  • Hess's law: the enthalpy change of a reaction is independent of the route taken, provided the initial and final conditions are the same.
  • It follows from conservation of energy: no route can create or destroy energy.
  • So a ΔH you can't measure = the sum of ΔH values you can.
Mission 6

Three moves

  • Reverse an equation: change the sign of ΔH.
  • Multiply an equation: multiply ΔH by the same number.
  • Add equations: add their ΔH values. Species on both sides cancel.
  • Arrange the given equations so they add up to the target equation.
Mission 6

Worked example: carbon monoxide

Carbon monoxide cycleC(s) + O2(g)CO(g) + ½O2(g)CO2(g)target −110.5(1)−393.5(2)−283.0values in kJ mol−1with an arrow: + against an arrow: −
  • Target: C(s) + ½O2(g) → CO(g).
  • (1) C(s) + O2(g) → CO2(g), ΔH = −393.5 kJ mol⁻¹ · (2) CO(g) + ½O2(g) → CO2(g), ΔH = −283.0 kJ mol⁻¹.
  • Keep (1). Reverse (2): CO2(g) → CO(g) + ½O2(g), ΔH = +283.0.
  • Add: CO2 cancels, and ½O2 cancels from one side.
  • ΔH = −393.5 + 283.0 = −110.5 kJ mol⁻¹.
Quick check
?An exothermic reaction P → Q takes place in a single step. With a catalyst, the same reaction takes place by a different route of three steps with a lower activation energy, and is much faster. Both routes start from the same reactants and give the same products under the same conditions. How does ΔH of the catalysed reaction compare with ΔH of the uncatalysed reaction?
Mission 6

Drawing an enthalpy cycle

Carbon monoxide cycleC(s) + O2(g)CO(g) + ½O2(g)CO2(g)target −110.5(1)−393.5(2)−283.0values in kJ mol−1with an arrow: + against an arrow: −
  • Write the target reaction along the top, with its arrow.
  • Below, write what both sides can be converted into (here, CO2).
  • Draw arrows for the known ΔH values, in the direction they are measured.
  • Go round the other way: with an arrow, add ΔH; against an arrow, subtract it.
  • CO: ΔH = ΔH1 − ΔH2 = −393.5 − (−283.0) = −110.5 kJ mol⁻¹.
  • Unfamiliar cycles will be given to you: just follow the arrows.
Calculate
?Nitrogen monoxide from car exhausts is oxidised in the air: 2NO(g) + O2(g) → 2NO2(g). Calculate ΔH for this reaction from:
  • (1) ½N2(g) + ½O2(g) → NO(g), ΔH = +90.3 kJ mol⁻¹ · (2) ½N2(g) + O2(g) → NO2(g), ΔH = +33.2 kJ mol⁻¹. Answer in kJ mol⁻¹.
kJ mol⁻¹
Mission 6

Hess's law in the lab

Copper sulfate hydration cycleCuSO4(s) + 5H2O(l)CuSO4·5H2O(s)CuSO4(aq)ΔH = ?ΔH1−67.0ΔH2+11.0polystyrene cupexample resultskJ mol−1
  • Target: CuSO4(s) + 5H2O(l) → CuSO4·5H2O(s). You can't measure it in a cup: you can't add exactly 5H2O and stop at the solid.
  • Run 1: dissolve anhydrous CuSO4(s) in water. ΔH1 = −67.0 kJ mol⁻¹ (example result).
  • Run 2: dissolve CuSO4·5H2O(s) in water. ΔH2 = +11.0 kJ mol⁻¹ (example result).
  • Both end as the same solution, so ΔH = ΔH1 − ΔH2 = −67.0 − (+11.0) = −78.0 kJ mol⁻¹.
Quick check
?Use the enthalpy changes of reactions 1 and 2 to calculate ΔH for the decomposition of hydrogen peroxide: 2H2O2(l) → 2H2O(l) + O2(g). Reaction 1: H2(g) + O2(g) → H2O2(l), ΔH1 = −187.8 kJ mol⁻¹. Reaction 2: 2H2(g) + O2(g) → 2H2O(l), ΔH2 = −571.6 kJ mol⁻¹.
Mission check

?Graphite turns into diamond only at enormous pressures, so ΔH for C(s, graphite) → C(s, diamond) can't be measured directly. But both forms burn.
(1) C(s, graphite) + O2(g) → CO2(g), ΔH = −393.5 kJ mol⁻¹ · (2) C(s, diamond) + O2(g) → CO2(g), ΔH = −395.4 kJ mol⁻¹. What is ΔH for graphite → diamond?
Mission 7

Mission 7: Carbon and hydrogen don't combine cleanly to make methane. So how does the data booklet know its enthalpy of formation?

Make a guess: Carbon and hydrogen don't combine cleanly to make methane. So how does the data booklet know its enthalpy of formation?

Mission 7

Standard conditions and standard states

  • ⦵ means standard conditions: 100 kPa and a stated temperature, usually 298 K. Solutions: 1 mol dm⁻³.
  • Standard state of a substance: its pure, normal form under those conditions.
  • Examples: C(s, graphite), O2(g), Br2(l), H2O(l), Na(s).
Mission 7

Standard enthalpy of formation

  • ΔfH⦵: the enthalpy change when 1 mol of a compound is formed from its elements, with all reactants and products in their standard states, under standard conditions.
  • An element in its standard state: ΔfH⦵ = 0.
  • Use fractions to make exactly 1 mol: 2Al(s) + 1½O2(g) → Al2O3(s).
  • Start from elements, never from gaseous atoms such as C(g) or H(g).
Quick check
?Which equation represents the standard enthalpy change of formation, ΔfH⦵, of methanol, CH3OH(l)?
Mission 7

Standard enthalpy of combustion

  • ΔcH⦵: the enthalpy change when 1 mol of a substance burns completely in oxygen, with all reactants and products in their standard states, under standard conditions.
  • Complete: carbon ends as CO2(g), hydrogen as H2O(l).
  • Always negative. Elements burn too: C(s) and H2(g) have values.
Mission 7

Other standard enthalpy changes

  • Enthalpy change of reaction, ΔrH⦵: for the amounts in the equation as written, under standard conditions.
  • Neutralisation: the enthalpy change when 1 mol of water forms from an acid and an alkali, under standard conditions. Method in Mission 5.
  • Symbol: ΔneutH.
Quick check
?Which equation represents the standard enthalpy change of combustion of ethanol?
Mission 7

Using formation data: limestone

Formation cycle for limestone decomposingCaCO3(s)CaO(s) + CO2(g)Ca(s) + C(s) + 1½O2(g)target ΔH⦵−1207.6(−634.9)+ (−393.5)ΔfH⦵ values in kJ mol−1
  • Reactants and products can both be made from the same elements.
  • Hess's law then gives ΔH⦵ = ΣΔfH⦵(products) − ΣΔfH⦵(reactants).
  • Multiply each value by its coefficient. Elements in their standard states count as zero.
  • CaCO3(s) → CaO(s) + CO2(g)
  • ΔfH⦵ / kJ mol⁻¹: CaCO3(s) −1207.6, CaO(s) −634.9, CO2(g) −393.5.
  • ΔH⦵ = [−634.9 + (−393.5)] − [−1207.6] = −1028.4 + 1207.6 = +179.2 kJ mol⁻¹: endothermic.
Quick check
?Use the data to calculate the standard enthalpy change of combustion of ethane, C2H6(g). ΔfH⦵ / kJ mol⁻¹: C2H6(g) −84.0; CO2(g) −393.5; H2O(l) −285.8; H2O(g) −241.8.
Mission 7

Using combustion data

Combustion cycle for ethene plus hydrogenC2H4(g) + H2(g)C2H6(g)2CO2(g) + 3H2O(l)target ΔH⦵(−1411.0)+ (−285.8)+ 3½O2(g)−1560.7+ 3½O2(g)ΔcH⦵ values in kJ mol−1
  • Reactants and products all burn to the same CO2 and H2O.
  • So the order flips: ΔH⦵ = ΣΔcH⦵(reactants) − ΣΔcH⦵(products).
  • Elements that burn, C and H2, are not zero here.
  • C2H4(g) + H2(g) → C2H6(g). ΔcH⦵ / kJ mol⁻¹: C2H4 −1411.0, H2 −285.8, C2H6 −1560.7.
  • ΔH⦵ = [−1411.0 + (−285.8)] − [−1560.7] = −136.1 kJ mol⁻¹.
  • This is how ΔfH⦵ of methane is found: burn C, H2 and CH4 separately.
Calculate
?Ethyne can be hydrogenated to ethane: C2H2(g) + 2H2(g) → C2H6(g). ΔcH⦵ / kJ mol⁻¹: C2H2(g) −1301.1; H2(g) −285.8; C2H6(g) −1560.7. Calculate ΔH⦵ for the reaction, in kJ mol⁻¹.
kJ mol⁻¹
Mission check

?Propane can't be made cleanly from carbon and hydrogen. These reactions can be measured in a calorimeter:
(1) C(s) + O2(g) → CO2(g), ΔH = −393.5 kJ mol⁻¹ · (2) H2(g) + ½O2(g) → H2O(l), ΔH = −285.8 kJ mol⁻¹ · (3) C3H8(g) + 5O2(g) → 3CO2(g) + 4H2O(l), ΔH = −2219.2 kJ mol⁻¹. What is ΔfH⦵ of propane, for 3C(s) + 4H2(g) → C3H8(g)?
Recap

The big ideas

Mission 1

  • Rate = change in concentration (or volume, or mass) per unit time.
  • The rate at one instant is the gradient of the tangent at that time; the initial rate is the tangent at t = 0.
  • Two methods: continuous monitoring (one run, many readings) and initial rate (clock: rate ∝ 1/t).

Mission 2

  • Exothermic: system loses energy, surroundings warm, ΔH negative. Endothermic: system gains energy, surroundings cool, ΔH positive.
  • Profiles: ΔH from reactants to products; Ea from reactants to the top of the barrier.

Mission 3

  • ΔH = Σ(bonds broken) − Σ(bonds formed): exothermic when the bonds formed are stronger in total.
  • Mean (average) bond enthalpies give an estimate: values are averages, for gases only.

Mission 4

  • A reaction needs collisions with energy ≥ Ea; most collisions fail.
  • Concentration, pressure and surface area raise collision frequency; temperature mainly raises the fraction with E ≥ Ea; a catalyst lowers Ea.

Mission 5

  • q = mcΔT (m of the water or solution), then ΔH = −q ÷ n, with n for the limiting reactant.
  • Give ΔH with sign, in kJ mol⁻¹.
  • Correct for heat exchange by extrapolating the temperature–time graph to the time of mixing.

Mission 6

  • Hess's law: ΔH depends only on start and finish, so a hard-to-measure ΔH is the sum along another route.
  • Reverse → change the sign; multiply → multiply ΔH; add → add ΔH.
  • In a cycle: with an arrow add ΔH; against it subtract.

Mission 7

  • ΔfH⦵: 1 mol of compound from its elements in standard states (elements = 0). ΔH⦵ = ΣΔfH⦵(products) − ΣΔfH⦵(reactants).
  • ΔcH⦵: 1 mol burned completely; ΔH⦵ = ΣΔcH⦵(reactants) − ΣΔcH⦵(products). Standard: 100 kPa, usually 298 K.
🏆

Mini-lesson complete!

⭐⭐⭐

You've worked through Physical chemistry for OCR A-level Chemistry. 🎉

  1. Mission 1A speed camera clocks a car at one instant. How do you clock a reaction at one instant?
  2. Mission 2When a cold pack goes cold, has the chemical inside lost energy or gained it?
  3. Mission 3If breaking bonds takes in energy, how can burning a fuel give energy out?
  4. Mission 4Why can a cloud of flour dust explode, when a heap of flour only smoulders?
  5. Mission 5Where does half the energy go when you burn a fuel under a can of water?
  6. Mission 6Carbon always burns partly to CO2. So how do we know ΔH for making carbon monoxide?
  7. Mission 7Carbon and hydrogen don't combine cleanly to make methane. So how does the data booklet know its enthalpy of formation?

Your stars: 0 / 0

📣 Smashed it? Share your score

Challenge a friend to beat your stars, or show a parent how you got on.

→ Back to A-Level Chemistry · OCR